Theben PlanoCentro 000-A-230V Operating Manual Download Page 3

Page: 3 / 28

Thank you for purchasing a Theben HTS presence detector and putting your trust in us.

1. Safety

CAUTION!

Danger of death through electric shock or fire!

Installation should only be carried out by a qualified electrician!

Work done on electrical installations may only be conducted by an authorised electrician or

trained persons under the supervision and charge of an authorised electrician according to

electrotechnical regulations!

Observe country-specific safety guidelines for working on electric installations!

The voltage

supply must be disconnected before installation!

CAUTION!

The device is maintenance-free. The warranty terminates if the device is opened or entered with

any kind of object.

1.1 Designated use

The presence detector is intended for indoor installation.

The presence detector is solely intended for the purpose contractually specified between the

manufacturer and the user. Any other or extended use has to be regarded as not complying with

the designated use. The manufacturer is not liable for any resulting damage. Radio frequency has

to be followed.

Summary of Contents for PlanoCentro 000-A-230V





























Search results

Summary of Contents for PlanoCentro 000-A-230V

Reviews:

Related manuals for PlanoCentro 000-A-230V

Brands by name

Popular brands

Theben PlanoCentro 000-A-230V, Operating Manual

Search results

Summary of Contents for PlanoCentro 000-A-230V

Reviews:

Related manuals for PlanoCentro 000-A-230V

Brands by name

Popular brands