5
with the “theSenda P”. In this sense, the remote controls
serve as set-up aids. A range of variable parameters is availa-
ble for adjustment with the remote control (see section “Para-
meters via remote control”).
Settings via the button
Pressing the button for longer than 15 s triggers the teach-in
of the brightness setpoint value by the teach-in function. In
addition, the teach-in function can be conveniently executed
with the „SendoPro, theSenda B/App“ management remote
control or the “theSenda P” installation remote control (see
section “Control commands via remote control”).
The teach-in function via the button can be disabled using
the „SendoPro, theSenda B/App“ management remote
control when the “Configuration button” parameter is set to
“disabled”.
Parameters via remote control
The following parameters can be queried or changed via
the remote control for support during start-up as well as
servicing:
Parameter
Description
Can be
queried
Sendo-
Pro /
theSenda
B (App)
Can be
changed
Sendo-
Pro /
theSenda
B (App)
Can be
changed
theSenda
P
Function C1
Selection:
switching/control
x
x
Brightness set
point value C1
Value range in lux/
measurement off
x
x
x
Brightness
actual value C1
Query brightness
actual value
x
Room correction
factor mid
Room correction
factor
x
x
Brightness
measurement
value mid
Lux meter bright-
ness value in lux
x
Detection sensi-
tivity (PIR)
Value range in
increments
x
x
x
Lighting time
delay
Value range in
seconds and
minutes
x
x
Short presence
Short-term pre-
sence: On/Off
x
x
Energy saving
mode
Selection: eco/eco
plus
x
x
Presence switch-
on delay
Value range in
seconds/minutes
x
Presence time
delay
x
x
Switch-on dim-
ming value C1
Value range in %
x
Configuration
type C1
Selection: auto/man
x
x
x
Control speed
Selection: standard/
medium/fast
x
Minimum dim-
ming value
Value range in %
x
Maximum dim-
ming value
Value range in %
x
Switch off
brightness
Value range in
minutes/hours/
never off
x
Manual dimming
response
Selection: school/
office
x
Standby time
Value range in
seconds/minutes/
permanently on
x
Parameter
Description
Can be
queried
Sendo-
Pro /
theSenda
B (App)
Can be
changed
Sendo-
Pro /
theSenda
B (App)
Can be
changed
theSenda
P
Standby dim-
ming value
Value range in %
x
IR group address
C1
Selection: all/I/II/III
x
Scene 1 C1
Value range in %
x
Scene 2 C1
Value range in %
x
Configuration
button
Selection: enabled /
disabled
x
LED display
motion
Off/On
x
The parameters are sent to the presence detector with the
„SendoPro, theSenda B/App“ management remote control or
with the “theSenda P” installation remote control via infra-red.
Changed parameters are applied and used by the detector.
With the „SendoPro, theSenda B/App“ management remote
control, parameters can be queried by sending values level-
by-level to the detector. If the sent value is below the set
parameter, the LED illuminates briefly. If the sent value is
equal or above the set parameter, the LED flickers for 2 s.
Function C1
The channel C1 light can be operated in the switching opera-
tion or constant lighting control function. Settings are made
via the “Function C1” parameter.
Value range (with the „SendoPro, theSenda B/App“)
Switching
Channel C1 light is in the switching operating function
Control
Channel C1 light is in the constant lighting control function
Further information can be found in the section “4. Function”,
under the “Channel C1 light” section on page 1.
Brightness set point value C1
The brightness setpoint value defines the minimum required
brightness. The currently prevailing brightness is measured
below the presence detector. If the prevailing brightness is
below the setpoint value, the light is switched on when a
presence is detected (in configuration type fully automatic
device).
Value range
•
Lux values with „SendoPro, theSenda B/App“ manage-
ment remote control: 10 – 3000 lux, measuring off
•
The following values are available with the “theSenda
P” installation remote control: 10, 15, 300, 500, 800 lux,
measuring off ( button)
•
The currently measured brightness value (lux) can be
adopted as a new brightness setpoint value with the
„SendoPro, theSenda B/App“ management remote con-
trol by using the teach-in control command, or with the
“theSenda P” installation remote control via the teach-in
button. Values outside the permitted range will auto-
matically be set to the appropriate limit value.
