manualshive.com logo in svg

Thames & Kosmos Candy Claw Machine, Experiment Manual, Page: 2 / 20

Share
Download
Thames & Kosmos Candy Claw Machine Experiment Manual Download Page 2

A

B

C

P6 P12

P7

P13

P19

P14

P20

P18

P21

P11

P22

P15

P5

P2

P3

P8

P9

P10

P16

P1

P4

P23

P24

P17

P25

P26

P27

4x

4x

3x

2x

2x

2x

4x

2x

2x

2x

 

    

KIT CONTENTS

What’s inside your experiment kit:

Checklist:

 

No.   Description  

Qty. 

  A 

Plastic frame A (Parts A1 –A17)  1

  B 

Plastic frame B (Parts B1 – B9) 

1

  C 

Plastic frame C (Parts C1 – C13)  1

  P1  Base tray 

1

  P2  Base front panel 

1

  P3  Back leg 

2

  P4  Top frame 

1

  P5  Worm screw 

1

  P6  Column (2 left and 2 right) 

4

  P7  Mounting panel for crank 

1

  P8  Prize door 

1

  P9  Prize ejector tray   

1

  P10  Prize chute frame 

1

  P11  Prize trigger 

1

  P12  Worm screw housing 

1

  P13  Piston seal 

4

 

No.   Description  

Qty.

  P14  Suction cup 

3

  P15  Flexible drive shaft, 480 mm 

1

  P16  Flexible tubing (3x 450 mm,

 

 

and 1x 240mm) 

4

 P17  Rail 

2

  P18  Large piston spring 

2

  P19  Arm scissor spring 

2

  P20  Prize door spring 

1

  P21  Prize trigger spring 

1

 P22 Belt 

1

  P23  Large clear plastic panel 

2

  P24  Small clear plastic panel 

2

  P25  Die-cut sheet with 3 prize boxes  1
  P26  Sticker sheet 

1

 P27 Lollipops* 

6

Do you have any questions or are you 

missing any parts? Our tech support 

team will be happy to help you!

[email protected] 

or 1-800-587-2872

 

Good to know!

*Flavors and colors may vary.

Summary of Contents for Candy Claw Machine





















Reviews:

No comments