manualshive.com logo in svg

Texas Instruments TSW14J58 JESD204C, User Manual, Page: 11 / 23

Share
Download
Texas Instruments TSW14J58 JESD204C User Manual Download Page 11

3.3.3.3 JTAG Connectors

The TSW14J58EVM includes one industry-standard JTAG connector, P2, that connects to the JTAG port of the
FPGA. The USB 2.0 interface on the TSW14J58EVM allows for the FPGA to be programmed from the JTAG
connector or the USB 2.0 interface. The USB 2.0 interface allows the FPGA to be programmed using the HSDC
Pro software GUI. Every time the TSW14J58EVM is powered-down, the FPGA configuration is removed. The
user must program the FPGA through the GUI after every time the board is powered-up. The FPGA can also be
configured using the two on-board flash devices, U3 and U6.

FLASH DEVICES

 The TSW14J58EVM includes two serial flash programming EEPROMS that can load FPGA

firmware. From the factory, U3 is loaded with a file called JESD204B_1p4.mcs which will configure the FPGA to
operate in JESD204B mode. U6 is loaded with a file called JESD204C_1p4.mcs which will configure the FPGA
to operate in JESD204C mode. Jumper J35 determines which EEPROM will configure the FPGA when switch
SW4 is pressed. After power up, pressing SW4 will load the FPGA with the factory pre-programmed flash device
U3 if J35 has a shunt between pins 1-2 and U6 if the shunt is between pins 2-3 or removed.

Program the Memory Device

To program U3 and U6 with new files, use the following steps:

Note

Install Vivado

®

 version 2018.3 or later (Lab Edition)

1. Connect the TSW14J58 Capture card to the PC through a JTAG Xilinx Programmer cable. This will be the

JTAG connect P2.

2. Open the Vivado Installation:

• Double click “Open Hardware Manager”.

3. In the Hardware Manager, left click on “Open target” and select “Auto Connect”.
4. This will list all the FPGAs connected to the PC through JTAG Programmer cables.
5. Right click on “xcku5p_0” -> click on “Add Configuration Memory Device”.

Figure 3-1. Add Configuration Memory Device

6. In the pop-up window, search for the “mt25qu256-spi-x1_x2_x4” component. Click the 

OK

 button.

www.ti.com

Hardware Configuration

SLWU094 – MARCH 2021

Submit Document Feedback

TSW14J58 JESD204C Data Capture and

Pattern Generator Card

11

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for TSW14J58 JESD204C
























Reviews:

No comments