Texas Instruments TPS65917-Q1 Technical Reference Manual Download Page 106 | Manualshive

Page: 106 / 181

background image

FUNC_PAD_CONTROL Registers

106

SLVUAH1C – June 2015 – Revised April 2017

Submit Documentation Feedback

Copyright © 2015–2017, Texas Instruments Incorporated

Register Descriptions

3.9

FUNC_PAD_CONTROL Registers

lists the memory-mapped registers for the FUNC_PAD_CONTROL. All register offset

addresses not listed in

should be considered as reserved locations and the register contents

should not be modified.

Table 3-98. FUNC_PAD_CONTROL Registers

Address

Acronym

Register Name

Section

1F2h

OD_OUTPUT_CTRL2

Open Drain control register #2
RESET register domain: HWRST

1F4h

PU_PD_INPUT_CTRL1

Pull-up Pull-down control register #1
RESET register domain: HWRST
Note: It is user responsibility to take care about the pull-
up/pull-down selections versus the IO direction and type
(Open drain / Push-Pull)

1F5h

PU_PD_INPUT_CTRL2

Pull-up Pull-down control register #2
RESET register domain: HWRST
Note: It is user responsibility to take care about the pull-
up/pull-down selections versus the IO direction and type
(Open drain / Push-Pull)

1F6h

PU_PD_INPUT_CTRL3

Pull-up Pull-down control register #3
RESET register domain: HWRST
Note: It is user responsibility to take care about the pull-
up/pull-down selections versus the IO direction and type
(Open drain / Push-Pull)

1F8h

OD_OUTPUT_CTRL

Open Drain control register
RESET register domain: HWRST
Note: It is user responsibility to take care about the IO
direction and type (Open drain / Push-Pull) versus the
pull-up/pull-down selections

1F9h

POLARITY_CTRL

Polarity control register.
This register allows to invert the initial polarity of the
input or output pin.
RESET register domain: HWRST
Note: It is user responsibility to take care about the pull-
up/pull-down selections versus the IO polarity

1FAh

PRIMARY_SECONDARY_PAD1

PAD/PIN function register (Primary vs.
Secondary) #1
RESET register domain: HWRST

1FBh

PRIMARY_SECONDARY_PAD2

PAD/PIN function register (Primary vs.
Secondary) #2
RESET register domain: HWRST

1FCh

I2C_SPI

Validity memory
RESET register domain: HWRST

«
...
104
105
106
107
108
...
»

Summary of Contents for TPS65917-Q1






















































































































































































Reviews:

No comments

Related manuals for TPS65917-Q1

Brand: Paradox Pages: 28

Brand: R&S Pages: 60

Brand: GADGETMONSTER Pages: 26

Brand: LEGRAND Pages: 4

Brand: Moxa Technologies Pages: 2

ROTAPULS CK61 Series

Brand: Lika Pages: 2

Brand: Profi Power Pages: 17

Brand: Nyrius Pages: 11

Brand: ZIPPER MASCHINEN Pages: 52

Brand: Samlexpower Pages: 3

Brand: ZeeVee Pages: 7

Brand: SIIG Pages: 12

Brand: Sungrow Pages: 11

Brand: AGM Pages: 71

Brand: Telair Pages: 44

Brand: BZBGEAR Pages: 12

Brand: Linksys Pages: 39

Brand: Wavtech Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands