Texas Instruments TMS320C6722 User Manual Download Page 15 | Manualshive

Page: 15 / 114

background image

www.ti.com

2.7 Memory Map Summary

TMS320C6727, TMS320C6726, TMS320C6722

Floating-Point Digital Signal Processors

SPRS268E – MAY 2005 – REVISED JANUARY 2007

A high-level memory map of the C672x DSP appears in

Table 2-8

. The base address of each region is

listed. Any address past the end address must not be read or written. The table also lists whether the
regions are word-addressable or byte- and word-addressable.

Table 2-8. C672x Memory Map

DESCRIPTION

BASE ADDRESS

END ADDRESS

BYTE- OR WORD-ADDRESSABLE

Internal ROM Page 0 (256K Bytes)

0x0000 0000

0x0003 FFFF

Byte and Word

Internal ROM Page 1 (128K Bytes)

0x0004 0000

0x0005 FFFF

Byte and Word

Internal RAM Page 0 (256K Bytes)

0x1000 0000

0x1003 FFFF

Byte and Word

Memory and Cache Control Registers

0x2000 0000

0x2000 001F

Word Only

Emulation Control Registers (Do Not Access)

0x3000 0000

0x3FFF FFFF

Word Only

Device Configuration Registers

0x4000 0000

0x4000 0083

Word Only

PLL Control Registers

0x4100 0000

0x4100 015F

Word Only

Real-time Interrupt (RTI) Control Registers

0x4200 0000

0x4200 00A3

Word Only

Universal Host-Port Interface (UHPI) Registers

0x4300 0000

0x4300 0043

Word Only

McASP0 Control Registers

0x4400 0000

0x4400 02BF

Word Only

McASP1 Control Registers

0x4500 0000

0x4500 02BF

Word Only

McASP2 Control Registers

0x4600 0000

0x4600 02BF

Word Only

SPI0 Control Registers

0x4700 0000

0x4700 007F

Word Only

SPI1 Control Registers

0x4800 0000

0x4800 007F

Word Only

I2C0 Control Registers

0x4900 0000

0x4900 007F

Word Only

I2C1 Control Registers

0x4A00 0000

0x4A00 007F

Word Only

McASP0 DMA Port (any address in this range)

0x5400 0000

0x54FF FFFF

Word Only

McASP1 DMA Port (any address in this range)

0x5500 0000

0x55FF FFFF

Word Only

McASP2 DMA Port (any address in this range)

0x5600 0000

0x56FF FFFF

Word Only

dMAX Control Registers

0x6000 0000

0x6000 008F

Word Only

MAX0 (HiMAX) Event Entry Table

0x6100 8000

0x6100 807F

Byte and Word

Reserved

0x6100 8080

0x6100 809F

MAX0 (HiMAX) Transfer Entry Table

0x6100 80A0

0x6100 81FF

Byte and Word

MAX1 (LoMAX) Event Entry Table

0x6200 8000

0x6200 807F

Byte and Word

Reserved

0x6200 8080

0x6200 809F

MAX1 (LoMAX) Transfer Entry Table

0x6200 80A0

0x6200 81FF

Byte and Word

External SDRAM space on EMIF

0x8000 0000

0x8FFF FFFF

Byte and Word

External Asynchronous / Flash space on EMIF

0x9000 0000

0x9FFF FFFF

Byte and Word

EMIF Control Registers

0xF000 0000

0xF000 00BF

Word Only

(1)

(1)

The upper byte of the EMIF’s SDRAM Configuration Register (SDCR[31:24]) is byte-addressable to support placing the EMIF into the
Self-Refresh State without triggering the SDRAM Initialization Sequence.

Submit Documentation Feedback

Device Overview

15

«
...
13
14
15
16
17
...
»

Summary of Contents for TMS320C6722



















































































































Reviews:

No comments

Related manuals for TMS320C6722

Brand: Magiccos Pages: 2

Brand: JD Williams and Co Pages: 6

Brand: Gorenje Pages: 40

Brand: Gorenje Pages: 59

Brand: ECG Pages: 24

Brand: ECG Pages: 28

Brand: Wolf Garten Pages: 102

Brand: Vitek Pages: 4

Brand: T-Fal Pages: 14

Nagold Castline Stark

Brand: Hafele Pages: 12

Brand: Yamaha Pages: 8

Brand: JANE Pages: 108

Brand: Hamilton Beach Pages: 13

Brand: EAW Pages: 14

Brand: Taurus Pages: 55

Brand: LD Pages: 76

Brand: Mackie Pages: 15

Brand: Hyundai Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands