background image

iii

  Chapter Title—Attribute Reference

Preface

Related Documentation From Texas Instruments

J

THS7001 Programmable-Gain Amplifier (literature number
SLOS214) This is the data sheet for the THS7001 amplifier
integrated circuit used on the EVM. 

J

PowerPAD

 Thermally Enhanced Package (literature number

SLMA002) This is the technical brief for the special PowerPAD
package in which the THS7001 amplifier IC is supplied.

FCC Warning

This equipment is intended for use in a laboratory test environment only. It
generates, uses, and can radiate radio frequency energy and has not been
tested for compliance with the limits of computing devices pursuant to subpart
J of part 15 of FCC rules, which are designed to provide reasonable protection
against radio frequency interference. Operation of this equipment in other
environments may cause interference with radio communications, in which
case the user at his own expense will be required to take whatever measures
may be required to correct this interference.

Trademarks

TI is a trademark of Texas Instruments Incorporated.
PowerPAD is a trademark of Texas Instruments Incorporated.

Summary of Contents for THS7001





























Reviews: