Texas Instruments OMAP36 Series Technical Reference Manual Download

Page: 345 / 3738

Source selection/division

Hardware control

Software control

PRCM.CM_CLKSEL_CAM[4:0]

CLKSEL_CAM

Ratios: 1 to 16

CAM_MCLK

PRCM.CM_FCLKEN_CAM[0]

EN_CAM

L3_ICLK

CAM_L3_ICLK

PRCM.CM_ICLKEN_CAM[0]

EN_CAM

PRCM.CM_AUTOIDLE_CAM[0]

AUTO_CAM

PRCM.CM_CLKEN_PLL[18:16]

EN_PERIPH_DPLL

PRCM.CM_AUTOIDLE_PLL[5:3]

AUTO_PERIPH_DPLL

DPLL4_ALWON_FCLK

PRCM.CM_CLKSEL2_PLL[19:8]

PERIPH_DPLL_MULT

CM_CLKSEL2_PLL[6:0]

PERIPH_DPLL_DIV

prcm-066

L4_ICLK

CAM_L4_ICLK

Source selection/division

Hardware control

Software control

USBHOST_120M_FCLK

PRCM.CM_FCLKEN_USBHOST[1]

EN_USBHOST2

PRCM.CM_FCLKEN_USBHOST[0]

EN_USBHOST1

120M_FCLK

USBHOST_48M_FCLK

L4_ICLK

prcm-091

L3_ICLK

48M_FCLK

OSC_SYS_CLK

PRCM.PM_PWSTCTRL_USBHOST[4]

SAVEANDRESTORE

PRCM.CM_ICLKEN_USBHOST[0]

EN_USBHOST

PRCM.CM_AUTOIDLE_USBHOST[0]

EN_USBHOST

USBHOST_SAR_FCLK

USBHOST_L3_ICLK

USBHOST_L4_ICLK

Public Version

www.ti.com

PRCM Functional Description

Figure 3-69. CAM Power Domain Clock Controls

Table 3-53. CAM Power Domain Clock-Gating Controls

Clock Name

Reset

Clock-Gating Control

Gating Description

CAM_MCLK

Stopped

PRCM.

CM_FCLKEN_CAM

[0] EN_CAM

Gated when the enable bit is set to 0

CAM_L3_ICLK

Stopped

PRCM.

CM_ICLKEN_CAM

[0] EN_CAM,

Gated when:

PRCM.

CM_AUTOIDLE_CAM

[0] AUTO_CAM

• Enable bit is set to 0.

• Enable-autoidle bit pair is set to 1, and

the clock is not requested by
subsystem.

CAM_L4_ICLK

Stopped

3.5.3.7.10 USBHOST Power Domain Clock Controls

Figure 3-70

shows the clock controls for the USBHOST power domain.

Table 3-54

lists the clock-gating

controls for the USBHOST power domain.

Figure 3-70. USBHOST Power Domain Clock Controls

Table 3-54. USBHOST Power Domain Clock-Gating Controls

Clock Name

Reset

Clock-Gating Control

Gating Description

USBHOST_48M_FCL Stopped

PRCM.

CM_FCLKEN_USBHOST

[0] EN_USBHOST1

Gated when the enable bit is set to 0

345

SWPU177N – December 2009 – Revised November 2010

Power, Reset, and Clock Management

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands

Texas Instruments OMAP36 Series, Technical Reference Manual

Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands