Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 3426 / 3738

background image

Public Version

MMC/SD/SDIO Register Manual

www.ti.com

Table 24-37. MMCHS_SYSSTATUS

Address Offset

0x014

Physical Address

0x4809 C014

Instance

MMCHS1

0x480A D014

MMCHS3

0x480B 4014

MMCHS2

Description

System Status Register
This register provides status information about the module excluding the interrupt status information

Type

R

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

Reserved

RESETDONE

Bits

Field Name

Description

Type

Reset

31:1

Reserved

Reserved bit field. Do not write any value.

R

0x00000

000

0

RESETDONE

Internal Reset Monitoring

R

0

Note: the debounce clock , the interface clock and the functional clock shall be
provided to the MMC/SD/SDIO host controller to allow the internal reset
monitoring.

Read 0x0:

Internal module reset is on-going

Read 0x1:

Reset completed.

Table 24-38. Register Call Summary for Register MMCHS_SYSSTATUS

MMC/SD/SDIO Integration

•

MMC/SD/SDIO Use Cases and Tips

•

Programming Flow

:

MMC/SD/SDIO Register Manual

•

MMC/SD/SDIO Register Summary

Table 24-39. MMCHS_CSRE

Address Offset

0x024

Physical Address

0x4809 C024

Instance

MMCHS1

0x480A D024

MMCHS3

0x480B 4024

MMCHS2

Description

Card status response error
This register enables the host controller to detect card status errors of response type R1, R1b for all cards
and of R5, R5b and R6 response for cards types SD or SDIO.
When a bit MMCi.

[I] is set to 1, if the corresponding bit at the same position in the response

[I] is set to 1, the host controller indicates a card error (MMCi.

CERR bit) interrupt status to avoid the host driver reading the response register (MMCi.

Note: No automatic card error detection for autoCMD12 is implemented; the host system has to check
autoCMD12 response register (MMCi.

) for possible card errors.

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

CSRE

3426

MMC/SD/SDIO Card Interface

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
3424
3425
3426
3427
3428
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

FrameSaver 9120

Brand: Paradyne Pages: 2

F-ZTAT H8/3048 Series

Brand: Renesas Pages: 34

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brand: NETGEAR Pages: 2

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

Digital Encoder Plus

Brand: IDT Pages: 98

Brand: NC-link Pages: 20

Brand: HighPoint Pages: 10

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

Brand: ADTRAN Pages: 20

Brand: Multi-Link Pages: 31

Brand: MicroNova Pages: 113

SRCSASPH16I - RAID Controller

Brand: Intel Pages: 28

Brand: ACTi Pages: 12

Compressor DW-CP04

Brand: Digital Watchdog Pages: 73

Brand: Advantech Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands