manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 3423 / 3738

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 3423

Public Version

www.ti.com

MMC/SD/SDIO Register Manual

Table 24-32. CMD18 Issuing

Register Name

Register Address

Value

Value Description

MMCHS1.

MMCHS_CON

0x4809C02C

0x00000000

MMC bus is in push-pull mode.

MMCHS1.

MMCHS_HCTL

0x4809C128

0x00000002

MMCHS controller's data bus width is set to 4.

MMCHS1.

MMCHS_IE

0x4809C134

0x107f0023

Enables CERR, CIE, CCRC, CC, TC, BRR, CTO, DTO,
DCRC, DEB and CEB events to occur.

MMCHS1.

MMCHS_ISE

0x4809C138

0x107f0023

Enables CERR, CIE, CCRC, CC, TC, BRR, CTO, DTO,
DCRC, DEB and CEB interrupts to rise.

MMCHS1.

MMCHS_CMD

0x4809C10C

0x123a0033

Sends CMD18 whose opcode is 18, response type is 48
bits, with CICE, DP, MSBS, BCE, DE, DDIR and CCCE
enabled.

MMCHS1.

MMCHS_ARG

0x4809C108

0x00000000

Not used

MMCHS1.

MMCHS_BLK

0x4809C104

0x00080200

(number_blocks << 16) | (block_length)

24.6.1.3.7 Dealing With High-Capacity Cards

Unlike standard-capacity cards, memory addressing mode for high-capacity cards (SDHC and HC MMC)
is in 512-byte block format instead of byte format. This means that byte and partial accesses are not
allowed with high-capacity cards.

The 32-bit wide argument configured in the

MMCHS_ARG

register and sent in data transfer commands

CMD17, CMD18, CMD24, and CMD25, carries the block index where the read/write should start and not
the 32-bit byte address.

For high-capacity cards, the block size is fixed at 512 bytes. Any data transfer, when the data bus is
involved, must be a multiple of 512 bytes.

The number of blocks for a high-capacity card, which determines the capacity of the card block_count x
512 bytes, is accessible through field C_SIZE in the card s CSD register version 2.0 for SD cards, or
through the SEC_COUNT field in the card s EXT_CSD register for MMC cards compliant with MMC
specification version 4.x.

To write/read a packet whose size is less than 512 bytes to/from a high-capacity card, write/read the
whole 512-byte block that contains the range of bytes to modify/read.

24.7 MMC/SD/SDIO Register Manual

24.7.1 MMC/SD/SDIO Instance Summary

Table 24-33. Instance Summary

Module Name

Base Address

Size

MMCHS1

0x4809 C000

4K byte

MMCHS2

0x480B 4000

4K byte

MMCHS3

0x480A D000

4K byte

24.7.2 MMC/SD/SDIO Registers

24.7.2.1 MMC/SD/SDIO Register Summary

Table 24-34. MMC/SD/SDIO Register Summary

MMCHS1

MMCHS2

Register Width

MMCHS3 Physical

Register Name

Type

Address Offset

Physical

Physical

(Bits)

Address

Address

Address

MMCHS_SYSCONFIG

RW

32

0x0000 0010

0x4809 C010

0x480B 4010

0x480A D010

MMCHS_SYSSTATUS

R

32

0x0000 0014

0x4809 C014

0x480B 4014

0x480A D014

MMCHS_CSRE

RW

32

0x0000 0024

0x4809 C024

0x480B 4024

0x480A D024

3423

SWPU177N – December 2009 – Revised November 2010

MMC/SD/SDIO Card Interface

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments