Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 3082 / 3738

background image

Public Version

McBSP Integration

www.ti.com

NOTE:

OFF means this clock can be switched-off.

ON means this clock must be maintained during wake up period.

CAUTION

The

PRCM

module

does

not

have

any

hardware

mean

to

read

CLOCKACTIVITY settings. It is thus software responsibility to ensure a
consistent programming between McBSPi.

MCBSPLP_SYSCONFIG_REG

CLOCKACTIVITY bit field and PRCM 96M_FCLK and L4_ICLK control bits (for
more information about clocks, see

Section 21.3.2.2

, Clocks). If McBSP module

is disabled in both CM_FCLKEN and CM_ICLKEN PRCM registers while
CLOCKACTIVITY is set to 11, nothing prevents the PRCM module from
asserting its idle request which will be acknowledged regardless of the features
associated with the McBSP clocks. This may lead to unpredictable behaviors.

The software can disable all clocks at the McBSP module level by setting the IDLE_EN bit in
McBSPi.

MCBSPLP_PCR_REG

[14] registers. The IDLE_EN bit allows stopping all the clocks in the

McBSP module (legacy):

•

When set to ‘0’, the McBSP module is running

•

When set to ‘1’, the clocks in the McBSP module are shut off when both IDLE_EN =1 and his power
domain is in idle mode.

21.3.2.4.3 Wake-Up Capability

When configured in Smart Idle mode, the sources for wake-up generation are a subset of the interrupt
sources. The wake up sources are enabled by setting the McBSPi.

MCBSPLP_SYSCONFIG_REG

[2]

ENAWAKEUP bit (wake up feature control):

•

Set to ‘0’, wake up capability is disabled

•

Set to ‘1’, wake up capability is enabled

The McBSPi_SWAKEUP signal is the McBSP module asynchronous wake-up signal sent to the PRCM
module when a wake-up generation is requested.

The wake up configurations are defined by setting the corresponding bits in the
McBSPi.

MCBSPLP_WAKEUPEN_REG

register.

21.3.2.4.3.1 Receive Wake-up

There are 4 receive possible wake up configurations:

•

MCBSPLP_WAKEUPEN_REG

[3] RRDYEN bit: The McBSP module asserts the

McBSPi_SWAKEUP request when the receive buffer reaches the high threshold value (RTHRESHOLD
value + 1) of the McBSPi.

MCBSPLP_THRSH1_REG

register. If the

MCBSPLP_IRQENABLE_REG

[3] RRDYEN bit is set to 1, the McBSP module sends an

interrupt (McBSPi_IRQ) request to the MPU or IVA 2.2 subsystems when exiting from idle mode
(interrupt will be asserted once the McBSPi.

MCBSPLP_IRQSTATUS_REG

[3] RRDY bit changes from

‘0’ to ‘1’, indicating that received data is ready to be read).

•

MCBSPLP_WAKEUPEN_REG

[2] REOFEN bit: The McBSP module asserts the

McBSPi_SWAKEUP request at the end of the frame. If the McBSPi.

MCBSPLP_IRQENABLE_REG

REOFEN bit is set to 1, the McBSP module sends an interrupt (McBSPi_IRQ) request to the MPU or
IVA 2.2 subsystems when exiting idle mode.

•

MCBSPLP_WAKEUPEN_REG

[1] RFSREN bit: The McBSP module sends a

McBSPi_SWAKEUP request to the PRCM module when a receive frame-sync pulse is detected while
the McBSP module is in idle mode. If the McBSPi.

MCBSPLP_IRQENABLE_REG

[1] RFSREN bit is set

to 1, the McBSP module sends an interrupt (McBSPi_IRQ) request to the MPU or IVA 2.2 subsystems
when exiting idle mode.

3082

Multi-Channel Buffered Serial Port

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
3080
3081
3082
3083
3084
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Brand: YASKAWA Pages: 34

Brand: AMD Pages: 20

Brand: Commell Pages: 9

PowerBeam AC Gen2

Brand: Ubiquiti Pages: 22

APS6-400 Series

Brand: Eaton Pages: 114

Brand: ZALMAN Pages: 4

Brand: Acces I/O products Pages: 5

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

Brand: Dolphin Pages: 9

Brand: A4Tech Pages: 7

Brand: Tektronix Pages: 178

dspstak 21262sx

Brand: Danville Signal Processing Pages: 35

Brand: Omron Pages: 6

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: Promise Technology Pages: 26

Brand: Laser Pages: 4

Brand: Sony Ericsson Pages: 93

Brand: EZCast Pro Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands