manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 3177 / 3738

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 3177

Public Version

www.ti.com

McBSP Register Manual

Table 21-74. MCBSPLP_XCERB_REG

Address Offset

0x0000 0044

Physical Address

0x4807 4044

Instance

McBSP1

0x4809 6044

McBSP5

0x4902 2044

McBSP2

0x4902 4044

McBSP3

0x4902 6044

McBSP4

Description

McBSPLP transmit channel enable register partition B

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

XCERB

Bits

Field Name

Description

Type

Reset

31:16

RESERVED

Read returns 0x0.

R

0x0000

15:0

XCERB

Transmit Channel Enable

RW

0x0000

XCERB n=0 Disables transmission of n-th channel in an
even-numbered block in partition B

XCERB n=1 Enables transmission of n-th channel in an
even-numbered block in partition B

Table 21-75. Register Call Summary for Register MCBSPLP_XCERB_REG

McBSP Functional Description

•

Using Eight Partitions

:

[0]

•

Using Two Partitions (Legacy Only)

:

[1]

McBSP Register Manual

•

McBSP Register Mapping Summary

:

[2] [3] [4] [5] [6]

Table 21-76. MCBSPLP_PCR_REG

Address Offset

0x0000 0048

Physical Address

0x4807 4048

Instance

McBSP1

0x4809 6048

McBSP5

0x4902 2048

McBSP2

0x4902 4048

McBSP3

0x4902 6048

McBSP4

Description

McBSPLP pin control register

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

FSXP

FSRP

FSXM

FSRM

XIOEN

RIOEN

CLKXP

CLKRP

CLKXM

CLKRM

SCLKME

IDLE_EN

DX_STAT

DR_STAT

CLKS_STAT

3177

SWPU177N – December 2009 – Revised November 2010

Multi-Channel Buffered Serial Port

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments