Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 2949 / 3738

background image

Public Version

www.ti.com

UART/IrDA/CIR Register Manual

Table 19-69. TCR_REG

Address Offset

0x018

Physical Address

See

to

Description

Transmission control register.

This register stores the receive FIFO threshold levels to start/stop transmission during hardware flow control.

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

RX_FIFO_TRIG_HALT

RX_FIFO_TRIG_START

Bits

Field Name

Description

Type

Reset

31:8

Reserved

Read returns 0.

R

0x000000

7:4

RX_FIFO_TRIG_ START

RX FIFO trigger level to RESTORE transmission (0 to 60)

RW

0x0

3:0

RX_FIFO_TRIG_ HALT

RX FIFO trigger level to HALT transmission (0 to 60)

RW

0xF

Table 19-70. Register Call Summary for Register TCR_REG

UART/IrDA/CIR Functional Description

•

:

•

FIFO Interrupt Mode

•

Register Access Modes

[4] [5] [6] [7] [8] [9]

•

UART/IrDA (SIR, MIR, FIR)/CIR Mode Selection

[10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] [21] [22] [23] [24] [25] [26]

•

[28] [29] [30] [31] [32] [33]

UART/IrDA/CIR Basic Programming Model

•

Hardware and Software Flow Control Configuration

:

[34] [35] [36] [37] [38] [39] [40] [41] [42] [43] [44] [45]

UART/IrDA/CIR Register Manual

•

UART/IrDA/CIR Register Summary

•

UART/IrDA/CIR Register Description

:

Table 19-71. MSR_REG

Address Offset

0x018

Physical Address

See

to

Description

Modem status register. UART mode only.

This register provides information about the current state of the control lines from the modem, data set, or
peripheral device to the MPU. It also indicates when a control input from the modem changes state.

Type

R

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

RI_STS

NRI_STS

CTS_STS

DSR_STS

NCD_STS

DCD_STS

NCTS_STS

NDSR_STS

2949

SWPU177N – December 2009 – Revised November 2010

UART/IrDA/CIR

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
2947
2948
2949
2950
2951
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Univerge SV8100

Brand: NEC Pages: 44

Brand: 2N Pages: 11

Brand: 2N Pages: 5

Brand: 2N Telekomunikace Pages: 24

Brand: Yamaha Pages: 4

Brand: Xinje Pages: 57

Brand: STONEFLY Pages: 48

Brand: Acqiris Pages: 22

Kinetic FLT 80 D5/DDC Body

Brand: EK-Quantum Pages: 16

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: A4Tech Pages: 7

Procont LMC-008-IO

Brand: janitza Pages: 28

Brand: Digi Pages: 116

Vocal Performer VE-20

Brand: Boss Pages: 20

Brand: Navitar Pages: 1

Brand: Net Optics Pages: 2

Brand: H3C Pages: 62

EK-FC670 GTX Series

Brand: ekwb Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands