Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 1959 / 3738

background image

Public Version

www.ti.com

Display Subsystem Register Manual

Bits

Field Name

Description

Type

Reset

0

DSI_PLL_AUTOMODE

Automatic update mode.

RW

0x0

If this bit is set then the configuration updates will be
synchronized to DISPC_UPDATE_SYNC.
If this bit is clear configuration updates will be done immediately.

0x0: Manual mode

0x1: Automatic mode

Table 7-447. Register Call Summary for Register DSI_PLL_CONTROL

Display Subsystem Functional Description

•

DSI-PLL Power FSM

:

Display Subsystem Basic Programming Model

•

DSI PLL Go Sequence

[2] [3] [4] [5]

Display Subsystem Use Cases and Tips

•

Set Up DSI DPLL

•

Configure DSI PLL

:

Display Subsystem Register Manual

•

DSI PLL Controller Register Mapping Summary

Table 7-448. DSI_PLL_STATUS

Address Offset

0x0000 0004

Physical Address

0x4804 FF04

Instance

DSI_PLL_CTRL

Description

This register contains the status information

Type

R

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

DSI_PLL_LIMP

DSI_PLL_LOCK

DSI_PLL_RECAL

DSI_PLL_BYPASS

DSS_CLOCK_ACK

DSI_BYPASSACKZ

DSI_PLL_LOSSREF

DSI_PLL_HIGHJITTER

DSIPROTO_CLOCK_ACK

DSI_PLLCTRL_RESET_DONE

Bits

Field Name

Description

Type

Reset

31:10

RESERVED

Reserved. Reads return zero.

R

0x000000

9

DSI_BYPASSACKZ

State of bypass mode on PHY and HSDIVIDER

R

0x0

0x0: DSI_PHY and HSDIVIDER have switched to using the bypass
clocks.

0x1: PLL outputs are still being used by DSI_PHY or HSDIVIDER

8

DSIPROTO_

Acknowledge for enable of DSI Protocol Engine clock

R

0x0

CLOCK_ACK

Verify the status before selecting this source in the DSI Protocol
Engine clock mux

0x0: DSI Protocol Engine clock inactive

0x1: DSI Protocol Engine clock active

7

DSS_CLOCK_ACK

Acknowledge for enable of DSS clock

R

0x0

Verify the status before selecting this source in the DSS clock
multiplexer

0x0: DSS clock inactive

0x1: DSS clock active

1959

SWPU177N – December 2009 – Revised November 2010

Display Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
1957
1958
1959
1960
1961
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Brand: Paradyne Pages: 22

Brand: Hama Pages: 4

Brand: Lattice Semiconductor Pages: 15

Brand: QSC Pages: 28

Brand: Qualys Pages: 2

Brand: TC Electronic Pages: 55

Brand: 3Com Pages: 16

Brand: IDT Pages: 281

DMX-Universal-Demux

Brand: DMX4ALL Pages: 17

Brand: Rockwell Automation Pages: 108

Brand: FS Pages: 19

Proventia A1204

Brand: Internet Security Systems Pages: 42

Brand: Paradyne Pages: 10

Brand: 3Com Pages: 12

Brand: Xtreme Pages: 83

Brand: Vacron Pages: 16

Brand: Westermo Pages: 22

Brand: Paradyne Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands