Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 1739 / 3738

background image

Public Version

www.ti.com

Display Subsystem Basic Programming Model

NOTE:

This software reset is optional as an hardware reset is always performed on the DSI

protocol engine at device reset.

7.5.4.2

Power Management

The power management behavior of the DSI protocol engine is controlled by the DSS.

register. This register completely controls the way the module interferes with the PRCM module. The
DSS.

[0] AUTO_IDLE bit should be set to 1 (default value) to enable automatic clock

gating in the module.

7.5.4.3

Interrupts

There is a single interrupt request: DSI_IRQ. This interrupt line is merged with another interrupt line from
the DISPC_IRQ in a single interrupt request DSS_IRQ. The DSI_IRQ events are generated only for the
enabled VC(s). Two registers are used to enable and monitor the DSI interrupt events:
•

DSS.

register: This register indicates the enabled/disabled event for the VCs. Each

event for the VC is configured in the DSS.

DSI_VCn_IRQENABLE

register dedicated to the VC number.

In addition, it includes one bit for the enable of error reporting for the complex I/O: Error signaling from
the complex I/O: The interrupt is triggered when any error is received from the complex I/O
(ErrSyncEsc[4:0], ErrEsc[4:0] (edge trigger interrupt), ErrControl[4:0] and ErrContentionLP0[4:0],
ErrContentionLP1[4:0] from the complex I/O).

•

DSS.

register : The register

flags which VC(s) is/have generated

an interrupt. Based on the VC number, the register

DSI_VCn_IRQSTATUS

indicates the event

generating the interrupt. In addition, it includes one bit for the status of error reporting for the complex
I/O.

7.5.4.4

Global Register Controls

Prior to receive data from the DSI complex I/O, the DSI_PHY_SCP registers in the DSI complex I/O must
be configured. Refer to

for more details.

details the register access width

limitations for all the DSI modules.

Table 7-63. Register Access Width Limitations

Register Name

Register Access Width

All DSI complex I/O register

32-bit only

(DSI_PHY_SCP)

All DSI PLL control module registers

32-bit only

DSI_VCn_LONG_PACKET_HEADER

32-bit only

DSI_VCn_SHORT_PACKET_HEADER

32-bit only

DSI_VCn_LONG_PACKET_PAYLOAD

16-bit, 32-bit

All others DSI protocol engine registers

8-bit, 16-bit and 32-bit

CAUTION

In case of different access width detailed in

, an OCP error is

generated in response to the write using SResp=ERR.

The DSI protocol engine is globally controlled by the DSS.

register. The interface to the

complex I/O is enabled by setting the DSS.

[0] IF_EN bit. When the interface is disabled, it is

possible to provide data to the TX FIFO and read pending data in the RX FIFO. When the
DSS.

[0] IF_EN bit is set to 1, the pending packets should be sent to the DSI complex I/O, the

data transfer from the video port should be ignored only when received the next Vertical Sync Event which
is received but not send to the DSI complex I/O.

1739

SWPU177N – December 2009 – Revised November 2010

Display Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
1737
1738
1739
1740
1741
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Brand: 3Com Pages: 8

Brand: Baicells Pages: 8

Brand: Datasat Pages: 32

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

Brand: Idis Pages: 86

Brand: Paradyne Pages: 2

F-Tile SDI II Intel Agilex

Brand: Intel Pages: 39

Brand: red lion Pages: 5

Brand: AMX Pages: 1

Brand: Technics Pages: 20

Brand: Cowlacious Designs Pages: 8

2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011

Brand: Intel Pages: 172

Brand: MSI Pages: 90

Ready Made Curtain

Brand: Kvadrat Pages: 10

Brand: Nokia Pages: 3

Brand: Nokia Pages: 2

Brand: Nokia Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands