Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 1254 / 3738

background image

Public Version

Camera ISP Basic Programming Model

www.ti.com

The 32-bit destination addresses of the pixel data are set by the

CCP2_LCx_DAT_PING_ADDR

and

CCP2_LCx_DAT_PONG_ADDR

registers.

NOTE:

The destination address must be aligned on a 32-byte boundary; the address 5 LSBs are

ignored. The pixel data lines are packed together at the destination address.

It is possible to perform double-buffering (ping-ponging) at the destination by setting different addresses in
the

CCP2_LCx_DAT_PING_ADDR

and

CCP2_LCx_DAT_PONG_ADDR

registers. It is possible to disable

double-buffering by setting up the same address in both registers. The

[17]

PING_PONG status bit must be used by the software to determine which address contains the latest
frame.

A destination pitch controls the address jump between the address of the first pixel of the previous line
and the address of the first pixel of the current line. The destination pitch is set in bytes with the

CCP2_LCx_DAT_OFST

register. It applies for

CCP2_LCx_DAT_PING_ADDR

and

CCP2_LCx_DAT_PONG_ADDR

.

NOTE:

The destination pitch must be a multiple of 32 bytes; the address 5 LSBs are ignored.

The use of

CCP2_LCx_DAT_OFST

is limited to the following destination data formats:

•

YUV422 little endian

•

YUV422 big endian

•

EXP16

•

RGB565

•

EXP32

For all other data formats, the

CCP2_LCx_DAT_OFST

register is ignored (equivalent to

CCP2_LCx_DAT_OFST

= 0x0).

The destination data format is set with the

[7:2] FORMAT bit field.

For the PING frame:

•

@Line0 =

CCP2_LCx_DAT_PING_ADDR

•

@Line1 = @Line0 +

CCP2_LCx_DAT_OFST

•

@Line2 = @Line1 +

CCP2_LCx_DAT_OFST

For the PONG frame:

•

@Line0 =

CCP2_LCx_DAT_PONG_ADDR

•

@Line1 = @Line0 +

CCP2_LCx_DAT_OFST

•

@Line2 = @Line1 +

CCP2_LCx_DAT_OFST

When

CCP2_LCx_DAT_OFST

= 0x0, the lines are written contiguously in memory. The destination pitch

enables 2D transfers; it is required to write the pixel data directly in the frame buffer, for instance.

In such cases,

CCP2_LCx_DAT_OFST

= FRAME_BUFFER_WIDTH.

shows the pixel data

settings.

1254

Camera Image Signal Processor

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
1252
1253
1254
1255
1256
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Brand: D-Link Pages: 38

Web Smart DES-1210-28P

Brand: D-Link Pages: 6

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 23

Express EtherNetwork DI-604

Brand: D-Link Pages: 7

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 97

Brand: Data Translation Pages: 98

ThunderLAN TNETE100A

Brand: Texas Instruments Pages: 179

Brand: IFM Electronic Pages: 14

Brand: Freescale Semiconductor Pages: 8

NVRx-7300 series

Brand: Swann Pages: 9

Brand: QTech Pages: 406

Brand: AXIOMTEK Pages: 2

Brand: Unex Pages: 27

Brand: Rockwell Automation Pages: 21

Powereta iQP Series

Brand: TDK Pages: 2

Diamond Systems DS-MPE-CAN2L

Brand: Fortec Star Pages: 36

Brand: AMD Pages: 10

Brand: Maco Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands