manualshive.com logo in svg

Texas Instruments LDC3114, Manual

Share
Download
Texas Instruments LDC3114 Manual Download Page 23

7.5.1.17 INTPOL Register (Offset = 11h) [Reset = 18h] 

INTPOL is shown in 

INTPOL Register Field Descriptions

.

Return to the 

LDC3114 Registers

.

Interrupt polarity

Table 7-19. INTPOL Register Field Descriptions

Bit

Field

Type

Reset

Description

7-5

RESERVED

R/W

0h

Reserved

4

BTSRT_EN

R/W

1h

Enable reset of button algorithm baseline tracking value 

When this bit is not set, during transition between normal power 
mode to low power mode and back to normal power mode 

only 

baseline tracking value

 for enabled channels not reset. Other 

values in the button algorithm for calculating button press are reset 
even if this bit is not set.
0h = Disable Button Algorithm Restart
1h = Enable Button Algorithm Restart

3

BTN_ALG_EN

R/W

1h

Enable button press detection algorithm to assert events on 
OUT_x pins

When disabled, raw pre-processed data can be accessed via 
RAW_DATAx registers.
When disabled, interrupt on INTB pin is asserted when pre-
processed data capture is complete after active window period 
completion for any of the enabled channels or for error events.
When disabled, events on OUT_x pins pins are ignored to assert 
interrupt on INTB pin
0h = Disable Button Algorithm
1h = Enable Button Algorithm

2

INTPOL

R/W

0h

Interrupt Polarity

0h = Set INTB pin polarity to active low
1h = Set INTB pin polarity to active high.

1

DIS_BTN_TO

R/W

0h

Disable Button time-out if if button pressed for more than 50s.
0h = Enable Button Timeout
1h = Disable Button Timeout

0

DIS_BTB_MO

R/W

0h

Disable setting MAXOUT bit if button algorithm generates codes 
outside maximum range.
0h = Enable MAXOUT check
1h = Disable MAXOUT check

7.5.1.18 GAIN2 Register (Offset = 12h) [Reset = 28h] 

GAIN2 is shown in 

GAIN2 Register Field Descriptions

.

Return to the 

LDC3114 Registers

.

Gain for Channel 2 sensitivity adjustment for button algorithm

Table 7-20. GAIN2 Register Field Descriptions

Bit

Field

Type

Reset

Description

7-6

RESERVED

R/W

0h

Reserved

5-0

GAIN2

R/W

28h

Gain for Button Data for Channel 2

Refer to the Gain Table for detailed configuration.

7.5.1.19 LP_BASE_INC Register (Offset = 13h) [Reset = 05h] 

LP_BASE_INC is shown in 

LP_BASE_INC Register Field Descriptions

.

www.ti.com

LDC3114

SNOSDD0 – DECEMBER 2021

Copyright © 2021 Texas Instruments Incorporated

Submit Document Feedback

23

Product Folder Links: 

LDC3114

Summary of Contents for LDC3114
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands