manualshive.com logo in svg

Texas Instruments DS90UH927Q, Manual

Share
Download
Texas Instruments DS90UH927Q Manual Download Page 53

ADD

(dec)

ADD

(hex)

Register
Name

Bit(s)

Register

Type

Default

(hex)

Function

Description

208

0xD0

IND STS

7

RW

0x00

IA Reset

Indirect Access Reset
Setting this bit to a 1 will reset the I2C Master in
the HDCP Receiver. As this may leave the I2C bus
in an indeterminate state, it should only be done if
the Indirect Access mechanism is not able to
complete due to an error on the destination I2C
bus.

6

 

 

Reserved

5

RW

I2C TO
DIS

I2C Timeout Disable
Setting this bit to a 1 will disable the bus timeout
function in the I2C master. When enabled, the bus
timeout function allows the I2C master to assume
the bus is free if no signaling occurs for more than
1 second.

4

RW

I2C Fast

I2C Fast mode Enable
Setting this bit to a 1 will enable the I2C Master in
the HDCP Receiver to operation with Fast mode
timing. If set to a 0 (default), the I2C Master will
operate with Standard mode timing.

3:2

 

 

Reserved

1

R

IA ACK

Indirect Access Acknowledge
The acknowledge bit indicates that a valid
acknowledge was received upon completion of
the I2C read or write to the slave. A value of 0
(default) indicates the read/write did not complete
successfully.

0

R

IA DONE

Indirect Access Done
Set to a 1 to indicate completion of Indirect
Register Access. This bit will be cleared or read or
by start of a new Indirect Register Access.

209

0xD1

IND SAR

7:1

RW

0x00

IA SADDR Indirect Access Slave Address

This field should be programmed with the slave
address for the I2C slave to be accessed

0

RW

IA RW

Indirect Access Read/Write
0: Write (default)
1: Read

210

0xD2

IND OAR

7:0

RW

0x00

IA Offset

Indirect Access Offset
It is programmed with the register address for the
I2C indirect access.

211

0xD3

IND DATA

7:0

RW

0x00

IA Data

Indirect Access Data
For an indirect write, It is written with the write data.
For an indirect read, it contains the result of a
successful read.

240

0xF0

HDCP TX ID

7:0

R

0x5F

ID0

First byte ID code, ‘_’

241

0xF1

7:0

R

0x55

ID1

Second byte of ID code, ‘U’

242

0xF2

7:0

R

0x48

ID2

Third byte of ID code. ‘H'

243

0xF3

7:0

R

0x39

ID3

Forth byte of ID code: ‘9’

244

0xF4

7:0

R

0x32

ID4

Fifth byte of ID code: “2”

245

0xF5

7:0

R

0x37

ID5

Sixth byte of ID code: “7”

DS90UH927Q

Copyright © 1999-2012, Texas Instruments Incorporated

53

Summary of Contents for DS90UH927Q




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands