Texas Instruments AFE4403 User Manual Download Page 31

Page: 31 / 74

www.ti.com

AFE4403EVM Hardware

5.5

On-Board Key Interface

The EVM has 2 switches. The function of each switch is defined in

Table 4

Table 4. AFE4403EVM Switches

Switch Number

Description

SW1

This switch is used for hard reset of the board. The board resets and starts again with the firmware loaded.

SW2

This switch is used to enable boot strap loader (BSL) MSP430 firmware.

(1)

To enable BSL, disconnect device and then reconnect while holding down SW2. The device will appear as an HID device in the
device manager.

5.6

Visual Indication

The blue LED (LED3) indicates the USB power connection. The blue LED (LED1) indicates that the
microcontroller is busy servicing the requests from the PC application.

USB-Based Firmware Upgrade

The firmware on the AFE4403EVM can be changed from the PC application by selecting the

Firmware

Upgrade

menu option on the PC application. At the end of the firmware upgrade, the system issues a

reset command and reloads with new firmware. The firmware upgrade process steps are represented in
the screen shots below:

•

From the PC application, click on

File

→

Firmware Upgrade

•

A pop-up window opens as shown in

Figure 32

. Follow the instructions to continue to Firmware

Upgrade or to cancel the operation.

Figure 32. PC Application Firmware Upgrade – 1

•

The firmware upgrade application detects the connected EVM. (

Figure 33

)

SLAU572B – June 2014 – Revised July 2014

AFE4403 Development Guide

Submit Documentation Feedback

Summary of Contents for AFE4403











































































Search results

Summary of Contents for AFE4403

Reviews:

Related manuals for AFE4403

Brands by name

Popular brands

Texas Instruments AFE4403, User Manual

Search results

Summary of Contents for AFE4403

Reviews:

Related manuals for AFE4403

Brands by name

Popular brands