14
Sweeping. See Fig. 8C
The fan effect of the rotating line can be used for quick
and easy clearing up. Hold the line parallel to and
above the area to be swept and move the trimmer head
from right to left and opposite.
When cutting and sweeping you should use full
throttle to obtain the best results.
3-tooth blade.
It is used to cut through dense vegetation,
9. Rewinding the spool
Before any service and maintenance is done,
the power must be disconnected, it means the
battery removed from the tool.
See Fig. 9
The spool is supplied with the nylon line on it.
When need to rewind the spool with new nylon line,
follow these steps:
1. Press each side of cord housing. Remove lid.
2. Remove roll by pulling. Allow spring to remain on
spool. Remove any cord residue. Take 3-4 m of
cord (2.4 mm) and double it up.
3. Insert both ends into the 2 holes on the roll. Wind
cord onto roll in direction of arrow. Avoid twisting
cord. When twine is fully on roll, cut and insert the
two cut ends through the guide holes.
4. Assemble cord housing in reverse order, starting
with spring. Place cord in cord housing holes.
5. Re-place cover. Check cover is secure.
Always ensure trimmer head is secured tightly.
NEVER OVERFILL THE SPOOL WITH LINE!
10. Maintenance
Before any service and maintenance is done,
the power must be disconnected, it means the
battery removed from the tool.
•
Remove the battery before you clean and store the
machine.
•
Clean the housing and other parts with a soft brush
and a moist cloth. Never use aggressive cleansers
or solvents.
•
Prevent water from getting into the machine.
Lubrication of brushcutter gear
The gear is lubricated from the factory, but for every
30-hour operation grease must be refilled. Top up with
grease type: EP-0 using a grease gun (not included) on
the lubrication nipple. See Fig 10.
Lubrication of saw chain
•
Place saw on a flat surface
•
Remove the lid.
•
Add chain oil in the pruner container (top up).
Depending on the conditions you should add chain oil
for every 30-45 minutes of use, so check oil level often.
If the polesaw is used without chain oil, the chain will be
damaged.
Lubrication of hedge trimmer gear
The gearbox is lubricated from the factory, but for every
30-hour operation Grease must be refilled. Top up with
grease type: EP-0 using a grease gun (not included) on
the lubrication nipple. See fig. 10
The blades must be kept lubricated to prevent friction
and to extend the durability.
11. Storage
Store the trimmer dry and unavailable for children. It is
recommended not to let it rest on the trimmer head.
Hang it on a wall in the handle.
12. Specifications
Model BMZ
5800
Battery type
Lithium Ion
Battery nominal voltage
58V
Battery rated voltage
50.4V
Motor power max
1300W (input power)
Cutting width
25/40 cm
Trimmer head
Dual line tap’ n go
Trimmer line diameter
2.4 mm
Net weight (motor only)
4.5 kg
13. Warranty terms and conditions
The warranty period is 2 years for private end users in
EU countries. Products sold for commercial use, only
have a warranty period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are
NOT covered by the warranty.
Wearing parts, which are NOT covered for more than
12 months:
•
Trimmer head and spool
•
Nylon line, blade
•
Saw chain and guide bar
•
Hedge trimmer blade
•
Cutting guard and knife
•
Battery: If the battery is not stored correct (frost-
free and recharged every 3 months), the durability
is only guaranteed for 6 months.
The warranty does NOT cover damages/faults
caused by:
•
Lack of service and maintenance
•
Structural
changes
•
Exposure to unusual external conditions
•
If the machine has been improperly used or
overloaded
•
Use of unoriginal spare parts.
•
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is
determined in each case by an authorized service
center. Your receipt is your warranty note, why it
should always be kept safe.
REMEMBER:
The purchase of spare parts as well as
any request for warranty repair, art. number (e.g.
900700XX), year and serial number should always be
informed.
Summary of Contents for 90070064
Page 4: ...4 Fig 3 Fig 4 Fig 5 A B ...
Page 5: ...5 Fig 6 Fig 7 Fig 8 ...
Page 6: ...6 Fig 9 Fig 10 ...
