Texas Equipment 90063257, User Manual

Page: 10 / 26

10
3. Unpacking and assembly
Always wear gloves, when working with the
chain.
Chain and guide bar assembly
See Fig. 2+3+4
1. Remove battery (13)
2. Disengage the chain brake (3) pull the front hand
guard backwards Fig. 2.1
3. Unlock and undo the quick locking device (7) Fig
2.2, then remove the chain wheel guard (8) Fig. 2.3
4. Route the chain saw (4) onto the drive sprocket at
the guide bar (5). Make sure the chain teeth are
pointing forwards towards the tip of the guide bar.
Fig. 3
5. Fix the chain around the drive sprocket and mount
the guide bar on the chainsaw, so that the
fastening bolt fit into the keyway of the guide bar.
Fig. 3
6. Mount the chain wheel guard again F ig. 4.1 and
gently tighten the quick locking devise Fig.4.2
clockwise.
7. Adjust the chain by turn the chain tensioning wheel
Fig. 4.3 clockwise until the chain lies on the
underside of the guide bar. The chain is correctly
tensioned when it is still possible to raise it by 2-4
mm
4. Battery
Not included for solo machines*
To get the best performance of the chainsaw, it is
recommended to use the 4.0 Ah battery.
Warning: Do not try to disassemble, short circuit or put
it to extreme heat or fire, as it can cause serious inquiry
and permanent damage to the battery!
Battery pack is not fully charged when delivered.
Charging
•
Only use the original charger with
art. no. 90063242
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights Battery Pack
All LEDs are lit Fully charged (75-100%).
LED 1, LED 2, LED 3
are lit.
The battery pack is
50%-75% charged
LED 1, LED 2
are lit.
The battery pack is
25%-50% charged.
LED 1 are lit
The battery pack is
0%-25% charged
LED 1 flashes
The battery pack is empty.
Charge the battery.
Note: The indicator lighs is only indicative indications,
and is not accurate power indications.
Important:
To protect the battery from total
discharge, the machine will stop, when the battery is
nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can
continue.
5. Charger
A full charge takes around 60 min for 2.0 Ah batteri and
120 min for 4.0 Ah battery.
•
Only use the original charger*
•
Do not try to charge other type of batteries in the
charger, other than the original batteries with art.
no. 90063245 (2.0 Ah) or 90063246 (4.0 Ah).
•
Keep the charger in a dry and warm environment
(10-25 degrees C) and only use it indoor. It should
be connected to a normal 230V AC socket.
•
Before the battery is being used the first time, it is
recommended to charge it fully.
•
The surface of the battery can become warm
during charging. This is normal.
•
Do not cover battery or charger during charging.
Allow free ventilation of air.
Insert the battery into the slots of the charger and
slide it into place until it locks.
There are 4 lights on the charger indicating the status
and state of charge of the battery
Status
Charging
Fully charged
Evaluate
Defective
Important:
The charger will stop, when the battery is
full. However, it is not recommended to leave the
battery in charger for more than 24 hours.
It is recommended to drain the battery completely and
fully charge it whenever possible, as it can increase
the health of the battery. But partial charge will not
damage the battery.
To remove the battery from the charger, hold the
button down and pull the battery out.
Before winter storage, the battery should be fully
charged and kept warm at 10-20 degrees C. Charge it
every 3 months. Make sure to keep ventilation holes
clean and free from dirt.
Store the charger indoor between 5-25 degrees C.