25
HOW TO CHARGE THE BATTERY
NOTE: CHARGER IS NOT INCLUDED, BUT THE
BATTERY WILL SELF-CHARGE DURING USE!
WARNING:
When you charge the battery, do not
smoke. Keep the battery away from any sparks. The
fumes from the battery acid can cause an explosion
.
1. To disconnect the battery retainer from the battery
tray, push in on the lower end of the battery retainer.
2. Remove the battery from the right side of the unit.
3. Remove the protective caps from the battery
terminals.
4. Use a 12V battery charger to charge the battery.
Charge at a rate of 6 amperes for one hour. If you do
not have a battery charger, have an authorized
service center charge the battery.
5. Install the battery and secure with the battery retainer.
Make sure the positive (+) terminal is on the right
side.
HOW TO INSTALL THE BATTERY CABLES
WARNING: To prevent sparks, fasten the red cable to
the positive (+) terminal before you connect the black
cable.
Use the fasteners shown below to install the battery
cables. The fasteners are shown at full size.
(B) 14x79
(A) 2x82
1. Remove the protective caps from the battery
terminals.
2. Fasten the red cable to the positive (+) terminal with
the fasteners as shown (Figure 3).
3. Fasten the black cable to the negative (-) terminal
with the fasteners as shown.
IMPORTANT! BEFORE YOU START MOWING
1. Check the engine oil.
2. Fill the fuel tank with gasoline.
3. Check the level of the mower housing.
4. Check the air pressure of the tires.
5. Make sure the battery cables are attached.
WARNING:
Before doing any assembly or maintenance to the mower,
remove the wire from the spark plug.
NOTE:
In this instruction book, left and right describe the
location of a part with the operator on the seat.
How to prepare the engine
NOTE:
The engine was shipped from the factory filled with oil.
Check the level of the oil. Add oil as needed.
See the engine manufacturer’s instructions for the type of
gasoline and oil to use. Before you use the unit, read the
information on safety, operation, maintenance, and
storage.
WARNING:
Follow the engine manufacturer’s
instructions for the type of gasoline and oil to use.
Always use a safety gasoline container. Do not
smoke when adding gasoline to the engine. When
inside an enclosure, do not fill with gasoline.
Before you add gasoline, stop the engine.
Let the engine cool for several minutes.
CHECK THE LEVEL OF THE MOWER HOUSING
Make sure the level of cut is still correct. After you mow a
short distance, look at the area that was cut. If the mower
housing does not cut level, see the instructions on “How
To Level The Mower Housing” in the Maintenance section
of this instruction book.
CHECK THE TIRES
Check the air pressure in the tires. Tires with too much air
pressure will cause the unit to ride rough. Also, the wrong
air pressure will keep the mower housing from cutting
level. The correct air pressure (PSI) is 14 PSI (1 BAR).
The tires were over inflated for shipment.
Location of the controls
Illustration 5
BLADE ROTATION CONTROL (fig. 3)
Use the blade rotation control to start and stop the rotation
of the blade.
CLUTCH / BRAKE PEDAL (fig. 1)
The pedal has two
functions. The first function is a clutch. The second
function is a brake.
IGNITION SWITCH (fig. 2)
Use the ignition switch to start
and stop the engine.
SHIFT LEVER (fig. 4)
Use the shift lever to change the
speed of the unit.
LIFT LEVER (fig 6)
Use the lift lever to change the height
of cut.
PARKING BRAKE LEVER (fig. 7)
Use the parking brake
lever to engage the brake when you leave the unit.
THROTTLE CONTROL LEVER (fig. 5)
Use the throttle
control lever to increase or decrease the speed of the
engine.
HOW TO USE THE THROTTLE / CHOKE CONTROL
Use the throttle/choke control to choke the engine for cold
starts and increase or decrease the speed of the engine
(see Illustration 6).
1. Move the throttle/choke control completely forward to
the CHOKE position to start a cold engine.
2. The FAST position is marked with a detent. For
normal operation and when using a grass bagger,
move the throttle control
to the FAST position. For
maximum charging of the battery and for a cooler
running engine, operate the engine in the FAST
position.
3. The engine governor is set at the factory for maximum
performance. Do not adjust the governor to increase
the speed of the engine.
Summary of Contents for 7600E
