After Sales Support
TEL: 1300 663 907
After Sales Support
TEL: 1300 663 907
11
16
10. Press the OK button (22) to confirm the entered device
code. The message [SUCCESS] will appear for a few
seconds and the device returns to the previous menu
[CODE SET].
If the message [NOT FOUND] appears on the
display, the entered information was wrong and has
to been entered again. After a few seconds, the
display will return to the device code entry mode.
11. Quit the programming mode by pressing the EXIT button
(23) twice.
12. Verify the device functionality. If the device fails to respond
as desired, try the next device code from the list.
Searching for Device Codes Automatically
This method will scan all device codes for the selected device
type. This may take a very long time and should be used only
if the above methods do not succeed.
Switch on the device for which you want to program the
remote control. If your device is a VCR or a CD or DVD player,
please insert a tape or CD/DVD.
To cancel the following programming at any time,
press EXIT (23) to return without saving any changes.
Press the EXIT button (23) multiple times until the
remote control has returned to standard mode.
Press PAUSE (12) to cancel programming at any
time. Press PAUSE (12) again to resume the
programming from the same point.
Proceed as follows to search for the device code
automatically (this example refers to programming a TV set).
1. Point the remote control to the TV set while entering
the commands.
2. Press and hold the SET button (21) for at least 3 seconds.
The display shows [CODE SETUP]. Then release the
SET button (21).
3. Press the OK button (22). The display shows
[BRAND SRCH].
4. Press (8). The display shows [AUTO SRCH].
5. Press the OK button (22). The last selected device type
will show on the display. The device code below it
reads “0001”.
6. Press the source device selection button of the device
you want to program. In this example, it is the TV
button (2). The display shows [TV].
7. Make sure that the TV set has been powered on and
that the remote control points towards the TV set.
8. Press OK (22) to start the search. The remote control
will send a signal from each preset device code.
Macros
Macros allow you to execute up to 16 button commands
in sequence by just pressing one single button. The used
buttons may correspond to multiple devices.
For instance, press just one single button to perform
the following sequence of operations:
•
Power-up the TV set
•
Switch the TV set to the DVD player input source
•
Power on the DVD player
•
Start DVD playback
Programming a Macro
1. Press and hold the SET button (21) for at least 3 seconds.
The display shows [CODE SETUP]. Then release the SET
button (21).
2. Press (8) three times. The display shows [MACRO].
3. Press the OK button (22). The display shows [MACRO1].
If necessary, press the or (8) button to select
another sequential macro number to save your
macro. You can use the presets Macro1 to Macro6
for saving.
4. Press the OK button (22). The display shows [SET UP].
If you have chosen a preset and there is already
a macro stored under this position, the message
[MACRO HAS] will be displayed.
5. Press the OK button (22). The last selected device type
will show on the display.
6. First enter the source selection button of the device that
you want to execute the first command. To do this, press
the corresponding source selection button (2).
7. Press one or more buttons in sequence whose functions
shall be executed. You can execute up to 16 commands
in the same macro.
If you want to execute a function for a different
device, first press the corresponding source device
selection button (2). Switching the device will
diminish the number within the 16 programmable
commands.
8. After all the desired buttons have been programmed,
press the OK button (22). The message [SUCCESS] will
appear for a few seconds and the device returns to the
previous menu.
9. Quit the process by pressing the EXIT button (23)
two times.