background image

  

 

AXON AIX 101/103 (English) 

CE Declaration 

We: 

TerraTec Electronic GmbH, Herrenpfad 38, D-41334 Nettetal, Germany 

hereby declare that the product: 

AXON AIX 101 and AXON AIX 103 

to which this declaration refers is in compliance with the following standards or standardiz-
ing documents: 

EN 55013(2001)+A1(2003), EN 55020(2002). 

The following are the stipulated operating and environmental conditions for said compli-
ance: 

residential, business and commercial environments and small-company environments. 

This declaration is based on: 

Test report(s) of the EMC testing laboratory 

 

 

 

 

 

 

 

 

 

The information in this document is subject to change without notice and shall not be deemed as a 
warranty by the seller. No warranties, express or implied, are made with regard to the quality, suit-
ability or accuracy of this document. The manufacturer reserves the right to change the contents of 
this document and/or the associated products at any time without the provision of prior notice to 
specific persons or organizations. The manufacturer shall not be held liable for damages of any 
kind arising from the use, or the inability to use this product or its documentation, even if the possi-
bility of such damage is known. The information in this document is subject to copyright. All rights 
are reserved. No part of this manual may be reproduced or transmitted in any form or for any pur-
pose without the express written permission of the copyright holders. Product and brand names 
contained in this document are used for identification purposes only. All registered trademarks, 
product designations or brand names used in this document are the registered property of their 
respective owners. 

©TerraTec

®

 Electronic GmbH, 1994 - 2005. All rights reserved (10/28/2005). 

Summary of Contents for AXON AIX 101


























Reviews: