CHASSIS
2-7
ATLV 4300 330495 (10--98)
6. Remove the tension spring and clevis pin
from the brake cable clevis and arm on the
brake assembly.
7. Remove the two M12 hex screws and nyloc
nuts holding the brake assembly to the top
side of the wheel motor.
8. Pull the brake assembly straight up and off
the brake hub.
9. Remove the brake pads from the brake
assembly. Note the orientation of the pads.
10. Install the new brake pads in the same
orientation as the used ones.
11. Spread the new brake pads and slide the
brake assembly onto the brake hub.
12. Align the holes in the brake assembly with
the mount holes in the wheel motor.
13. Reinstall the hardware. Tighten to
64 -- 83 Nm (47 -- 61 ft. lb.)
14. Reinstall the clevis pin in the end of the
brake cable at the brake arm.
15. Reinstall the tension spring on the brake
arm.
16. Go to the operators compartment and press
the brake pedal on the side where the brake
pads were just replaced. Adjust the brake
cable if necessary. See TO ADJUST BRAKE
CABLE instructions in this section.
17. Engage the parking brake.
18. Reinstall the rear tire and wheel assembly.
19. Reinstall the five wheel nuts and tighten to
122 -- 162 Nm (90 -- 120 ft. lb).
20. Repeat this procedure on both sides of the
machine.
21. Tilt the hopper forward and lower the hopper
cover.
22. Remove the jack stands and lower the
machine.
23. Remove the blocks from the front tires and
disengage the parking brake.
24. Operate the machine and check the service
brakes for proper operation.
Summary of Contents for ATLV 4300
