background image

ENGLISH

EN

BR2020/T (04–98)

3

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is
designed to burnish smooth floors in an indoor
environment and is not constructed for any other
use. Use only recommended burnishing pads.

All operators must read, understand and
practice the following safety precautions.

The following safety alert symbol is used
throughout this manual as indicated in their
description:

WARNING: It warns the operator of

hazards and unsafe practices which could
result in severe personal injury or death.

CAUTION: It warns the operator of

unsafe practices which could cause damage
to the equipment.

The following information signals potentially
dangerous conditions to the operator or
equipment:

1.

DO NOT OPERATE, MAINTAIN OR
SERVICE MACHINE:

Unless trained and authorized.

Unless operator manual is read and
understood.

If it is not in proper operating
condition.

2.

WHEN OPERATING MACHINE:

Remove loose objects on floor. Loose
objects may become dangerous
projectiles if struck by revolving pad.

Keep hands and feet away from
revolving pad.

Keep machine moving to prevent
damage to finish or floor.

Do not run machine where flammable
liquids or gases are present.

Do not run on ramps or inclines
unless adequate personnel are present
for assistance.

Always use extreme caution when
maneuvering.

3.

BEFORE LEAVING OR SERVICING
MACHINE:

Make sure machine is turned off and
key is removed.

Stop on level surface.

Set parking brake if equipped.

Disconnect batteries.

WARNING: Always disconnect batteries

before servicing machine. Hazardous Voltage.
Shock or electrocution can result.

WARNING: Keep sparks and open flame

away. Batteries emit hydrogen gases,
explosion or fire can result.

WARNING: Charge batteries in a well

ventilated area and keep hood propped open.
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.

WARNING: Wear protective gloves and

shield eyes when servicing batteries. Battery
acid can cause burns.

CAUTION: Do not store outdoors and

avoid getting wet.

CAUTION: The use of supplies other than

those recommended by manufacturer may
cause damage.

RECOMMENDED STOCK ITEMS

Refer to the Parts List for recommended stock
items. Stock Items are clearly identified with a
Bullet preceding the parts description. See
example below:

Summary of Contents for 604777













Reviews: