Tennant 3640G/LP Service Manual Download Page 82

Page: 82 / 190

SWEEPING

3-32

3640G/LP 330585 (5--00)

4. Place the main brush lift lever in the down

position. Remove the retainer plate covering

the belt drive.

5. Place a screw driver in the 1/4 in. hole in the

brush arm behind the idler arm.

Place the

main brush lift lever in the up position.

The screw driver will hold the idler from

moving and tension on the brush belt will be

released.

NOTE: The pressure on the belt tensioner must

be released before the drive belt can be replaced.

6. Remove the brush belt from the engine

sheave, belt tensioner sheaves, and main

brush drive plug sheave.

7. Remove the screw holding the brush drive

plug to the pulley shaft. Remove the drive

plug and square key.

Summary of Contents for 3640G/LP































































































































































































Search results

Summary of Contents for 3640G/LP

Reviews:

Related manuals for 3640G/LP

Brands by name

Popular brands

Tennant 3640G/LP, Service Manual

Search results

Summary of Contents for 3640G/LP

Reviews:

Related manuals for 3640G/LP

Brands by name

Popular brands