Tennant 3640G/LP Service Manual Download Page 20

Page: 20 / 190

CHASSIS

2-4

3640G/LP 330585 (5--00)

REAR TIRES AND WHEELS

The rear tires and wheels drive the machine

through the transaxle. The tires are solid. Wide

track pneumatic tire are available as an option.

TO REMOVE REAR TIRE

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Place Shifter In Park.

1. Lift the rear of the machine by tipping the

machine back and placing blocks under the

machine frame in front of the wheels. Let the

machine go forward to contact the blocks.

The rear wheels will lift off the floor.

2. Remove the flat head screw holding the hub

cap to the drive wheel.

3. Pull the hub cap off the drive wheel.

4. Pull the tire and wheel assembly off the drive

axle. Be careful not to loose pin from axle

cross hole.

Summary of Contents for 3640G/LP































































































































































































Search results

Summary of Contents for 3640G/LP

Reviews:

Related manuals for 3640G/LP

Brands by name

Popular brands

Tennant 3640G/LP, Service Manual

Search results

Summary of Contents for 3640G/LP

Reviews:

Related manuals for 3640G/LP

Brands by name

Popular brands