Tenma 72-3555 Manual Download Page 51

Page: 51 / 58

Type

Name

Type

Name

Math Function

ExpFall

Trigonometric

Function

SinH

ExpRise

CosH

Log

SosInt

Cot

HaverSine

Tan

Lorentz

TanH

Dlorentz

Asin

Sqrt

AsinH

ARB x2

Acos

Cubic

ACosH

Gauss

Atan

LogNormal

AtanH12

Laplace13

Window Function

FlattopWin

Window Function

Boxcar

Hamming

Triang

Hanning

Blackman

Kaiser8

ChebWin

To get information about the Generator, press

Utility→System→System→About

No display/blank screen

If the screen is blank and has no display, even after the on/off button has been

pressed:

•

Make sure power supply is firmly connected to the Generator.

•

Make sure the master power switch on the rear panel is in good contact and has

been switched to “I”.

•

Restart the Generator

No Waveform Output

•

If th

e settings are correct, but there is no waveform output:

•

Make sure the BNC cable is properly connected to the channel output connector

•

Make sure

CH1

CH2

button has been pressed.

•

Save the current settings of the Generator to the USB, then restore the factory

settings and reboot the Generator.

Unable to recognise USB

•

Make sure the USB can work normally.

•

Make sure the USB in use is flash type, rather than hard-disc type as the

Generator does not support the latter.

TROUBLESHOOTING

Summary of Contents for 72-3555



























































Search results

Summary of Contents for 72-3555

Reviews:

Related manuals for 72-3555

Brands by name

Popular brands

Tenma 72-3555, Manual

Search results

Summary of Contents for 72-3555

Reviews:

Related manuals for 72-3555

Brands by name

Popular brands