Tempstar NAHA00101MH, Installation Instructions Manual

Page: 1 / 18

443 06 4001 01 June 2012
Specifications subject to change without notice.
NAHA00101MH
INSTALLATION INSTRUCTIONS
MANUFACTURED (MOBILE) HOME KIT
Condensing Gas Furnace Conversion
C E RT I F I E D
NOTE : Read the entire instruction manual before starting the
installation.
SAFETY CONSIDERATION
!
WARNING
FIRE, EXPLOSION, ELECTRICAL SHOCK, AND CARBON
MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal injury or
death.
This conversion kit shall be installed by a qualified service
agency in accordance with the manufacturer’s instructions
and all applicable codes and requirements of the authority
having jurisdiction. If the information in these instructions is
not followed exactly, a fire, explosion, or production of carbon
monoxide could result causing property damage, personal
injury, or loss of life. The qualified service agency is
responsible for the proper installation of this furnace with this
kit. The installation is not proper and complete until the
operation of the converted appliance is checked as specified
in the manufacturer’s instructions supplied with the kit.
!
AVERTISSEMENT
LE FEU, L’EXPLOSION, CHOC ELECTRIQUE, ET
MONOXYDE DE CARBONE EMPOISONNER
Cette trousse de conversion doit être installée par un servie
d’entretien qualifié, selon les instructions du fabricant et selon
toutes les exigences et tous les codes pertinents de l’autorité
compétente. Assurezvous de bien suivre les instructions
dans cette notice pour réduire au minimum le risque
d’incendie, d’explosion ou la production de monoxyde de
carbone pouvant causer des dommages matériels, de
blessure ou la mort. Le service d’entretien qualifié est
responsable de l’installation de cette trousse. L’installation
n’est pas adéquate ni complète tant que le bon
fonctionnement de l’appereil converti n’a pas été vérfié selon
les instructions du fabricant fornies avec la trousse.
Installing and servicing heating equipment can be hazardous
due to gas and electrical components. Only trained and
qualified personnel should install, repair, or service heating
equipment.
Untrained personnel can perform basic maintenance functions
such as cleaning and replacing air filters. Trained service
personnel must perform all other operations. When working on
heating equipment, observe precautions in the literature, on
tags, and on labels attached to or shipped with the unit, and
other safety precautions that may apply.
Follow all safety codes. In the United States, follow all safety
codes including the current edition of the National Fuel Gas
Code (NFGC) NFPA No. 54/ANSI Z223.1. In Canada, refer to
the current edition of the National Standard of Canada, Natural
Gas and Propane Installation Codes (NSCNGPIC),
CAN/CSA − B149.1 and .2. Wear safety glasses and work
gloves. Have a fire extinguisher available during start − up,
adjustment steps, and service calls.
Recognize safety information. This is the safety
− alert symbol
. When you see this symbol on the furnace and in
instructions or manuals, be alert to the potential for personal
injury. Understand the signal words DANGER, WARNING,
CAUTION and NOTE. The words DANGER, WARNING, and
CAUTION are used with the safety alert symbol. DANGER
identifies the most serious hazards which will result in severe
personal injury or death. WARNING signifies a hazard which
could result in personal injury or death. CAUTION is used to
identify unsafe practices which may result in minor personal
injury or product and property damage. NOTE is used to
highlight suggestions which will result in enhanced installation,
reliability, or operation.
INTRODUCTION
!
WARNING
FIRE, EXPLOSION, ELECTRICAL SHOCK AND CARBON
MONOXIDE POISONING HAZARD
Failure to follow instructions could result in personal injury,
death or property damage.
Improper installation, adjustment, alteration, service,
maintenance, or use can cause carbon monoxide poisoning,
explosion, fire, electrical shock, or other conditions, which
could result in personal injury or death. Consult your
distributor or branch for information or assistance. The
qualified installer or agency must use only factory − authorized
kits or accessories when servicing this product.
!
WARNING
FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury,
death or property damage.
Gas supply MUST be shut off before disconnecting electrical
power and proceeding with conversion.
This instruction covers the installation of kit Part No.
NAHA00101MH in the following gas furnaces for manufactured
(mobile) home applications.
This kit is only for use in single stage 40,000 through 120,000
Btuh gas input models when installed as a direct vent (2 − pipe)
furnace.
NOTE : This kit is not approved for the 140,000 Btuh gas input
model furnace, any two − stage and variable speed models, any
non − direct vent (1 − pipe) applications nor any furnace that does
not have a sealed combustion system with provisions for
outside air.
40,000 to 120,000 BTUH MODEL NUMBERS
BEGINNING WITH:
G9MXE F9MXE N9MXB N9MSB N9MSE