background image

Telpar, Inc. MTP Series Receipt Thermal Printer User Manual 

 

2011 Telpar, Inc. (Rev.20110809) 

Page 2 

Warranty

 

Telpar, Inc. 

— Printer Limited Warranty 

.

WARRANTIES  AND  DISCLAIMERS.  Products  manufactured  by  Telpar  are  warranted  against  defects  in 

workmanship  and  materials  for  a  period  of  twelve  (12)  months  from  the  date  of  shipment  to  the original user, 

provided  the  Product  (a)  remains  unmodified,  (b)  is  used  only  in  the  United  States  or  Canada,  (c)  is  operated 

under normal and proper conditions, as Telpar determines in its sole discretion, and (d) Customer provides prompt 

written notice Telpar of any defects as to parts and/or workmanship to.  Telpar may provide an extended warranty 

on certain Products or components thereof for an additional price determined solely by Telpar and such extended 

warranty  shall  only  be  effective  to  the  extent  memorialized  in  writing  by  Telpar.   Telpar’s  sole  obligation  and 

Customer’s  exclusive  remedy  for  defective  Telpar-manufactured Products  is  limited  to  repair  or  replacement,  as 

Telpar determines in its sole discretion.  The warranty described above does not include any labor or service costs 

for  removing  or  replacing  parts,  or  any  shipping  charges.   Any  repair  performed  by  Telpar  under  this  warranty 

does not extend the original warranty period of any Product.  This warranty shall not apply to any Product which 

has: (i) been repaired or altered, except by Telpar; (ii) not been maintained in accordance with all of the operating 

or  handling  instructions  supplied  by  Telpar,  or  (iii)  been  subjected  to  misuse,  willful  acts,  abuse,  tampering, 

negligence or accident, unusual physical or electrical stress, as Telpar determines in its sole discretion.  Customer 
acknowledges that Telpar provides no warranty for any third party materials and Telpar is not responsible and will 

have no liability for any items or services provided to Customer by any person or entity other than Telpar.  Telpar’s 

duty to perform under any warranty may be delayed, at Telpar’s sole option, until Telpar has been paid in full for 

all Products purchased by Customer.  No such delay shall extend the warranty period.  To obtain assistance under 

this  limited  warranty,  Customer  should  contact  the  selling  agency  or  write  to:  Telpar,  Warranty  Claims 

Department,  187  Crosby  Road,  Dover,  NH,  03820,  U.S.A.  Telephone:  800-872-4886  or  fax:  603-742-9938.   No 

person (including, without limitation, any agent, salesman, dealer or distributor) has the authority to act on behalf 

of  Telpar  to  expand  Telpar’s  obligation  beyond  the  terms  of  this  express  warranty,  or  to  state  that  the 

performance of the Product is other than published by Telpar.  For Products not manufactured by Telpar, to the 

extent  permitted  Telpar  assigns  to  Customer  the  benefits  of  any  warranties  provided  to  Telpar  by  the 

manufacturer(s)  of the Product.   THE FOREGOING IS A  LIMITED WARRANTY  AND IT IS THE ONLY WARRANTY 

PROVIDED BY TELPAR. TELPAR DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ALL IMPLIED 

WARRANTIES  OF  MERCHANTABILITY  AND  FITNESS  FOR  A  PARTICULAR  PURPOSE  AND  ALL  WARRANTIES  OR 

INDEMNITIES FOR PATENT OR COPYRIGHT INFRINGEMENT. IN NO EVENT SHALL TELPAR BE LIABLE FOR ANY 

INDIRECT,  INCIDENTAL,  SPECIAL  OR  CONSEQUENTIAL  DAMAGES,  INCLUDING  LOSS  OF  PROFITS,  REVENUE, 

DATA, OR USE, INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT OR 

TORT,  ARISING  OUT  OF  OR  RELATED  TO  THIS  AGREEMENT,  EVEN  IF  TELPAR  OR  ANY  OTHER  PERSONS  HAS 

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  TELPAR’S LIABILITY FOR DAMAGES HEREUNDER FOR 

ANY  CAUSE  WHATSOEVER  SHALL  IN  NO  EVENT  EXCEED  THE  AMOUNTS  RECEIVED  BY  TELPAR  FROM  THE 

CUSTOMER FOR THE PRODUCTS. TELPAR SHALL NOT BE RESPONSIBLE FOR ANY LOSS, DAMAGE OR EXPENSE 

OF ANY KIND CAUSED DIRECTLY OR INDIRECTLY BY THE USE OR PERFORMANCE OF THE PRODUCT PROVIDED 

HEREUNDER.  

 

 

Upon inspection, Telpar will make necessary repairs or replacement and return the merchandise, shipping prepaid. 

Summary of Contents for MTP-2242



















































Reviews: