background image

 

11

6 Installation guide 

6.1 Mounting 

  Test the GSM signal strength with your mobile phone. It may happen that the signal 

strength is not sufficient in the desired mounting place. In this case the planned 
installation place can be changed before mounting the device. 

  Do not mount the unit in places where it can be affected by strong electromagnetic 

disturbances (e.g. in the vicinity of electric motors, etc.). 

  Do not mount the unit in wet places or places with high degree of humidity. 

  The wires connected to the contact terminals should not be longer than 3 meters! 

  Connecting the GSM antenna: the GSM antenna can be fixed in the FME-M socket 

found on the panel. The antenna supplied with the module provides good 
transmission under normal reception circumstances. In case of occasionally 
occurring signal strength problems or/and wave interference (fading), use another 
(directed) type of antenna or find a more suitable place for the module. 

6.2  Putting into operation 

  Disable PIN code request, voicemail and notification in SMS about missed calls on 

the SIM card placed into the module. 

 

Enable caller ID sending service on the SIM card at the GSM service provider. 

 

If caller identification is used, this service must be enabled on the SIM card 
placed into the module (a few types of SIM cards do not have this function 
enabled by default). 

  Check the SIM card to be placed into its case properly. 

  Check the antenna to be fixed properly to the

 

Compact-GSM module.  

  Check the wires to be connected as instructed by the wiring diagram. 

  The device can be powered up. Make sure that the power supply is sufficient for the 

load of the module. The quiescent current of the module is 50mA, however it may 
increase up to 200mA during communication and relay control. 

7 Technical details 

7.1 Technical specification 

Supply voltage: 

9-30 VDC, 9-18VAC, 

 

or by using the serial diode: 18-30VAC 

Nominal current consumption:  50mA @ 12VDC,  27mA @ 24VDC 
Maximum current consumption: 200mA @ 12VDC,  100mA @ 24VDC 
Operating temperature: 

-20ºC - +70ºC 

Transmission frequency: 

GSM 900/1800, 850/1900 MHz 

Maximum relay output load: 

5A @ 24VAC/DC 

Dimensions: 

82 x 67 x 22mm 

Weight: 

80g (packed: 100g) 

7.2  Contents of the package 

 Compact-GSM module 

  GSM 900MHz / 1800MHz antenna 

  Plastic spacer support / snap fasteners 

 Diode 

  Application manual, warranty card 

 

Summary of Contents for Compact-GSM












Reviews: