Telit Wireless Solutions EZ10 Series Product Description Download | Manualshive

Page: 65 / 74

background image

Telit EZ10-GPRS/-PCS

Product Description

80269ST10014a, Rev. 3 – 26/09/05

Reproduction forbidden without written authorization by Telit Communications S.p.A.

Page 65 of 74

All Rights reserved – Right of modification reserved

5 Service and SW / Firmware Update

The RS232 serial interface on the Terminal used for the communication with a PC can also be
used to update the

Telit EZ10 Terminal Family

firmware (Software).

The firmware update can be done with a specific software tool provided by Telit that runs on
windows based PCs.

The update procedure requires to switch-on the Terminal at a prompt within the running
update tool. Thus, the power supply line shall be disconnected before the launch of the
update tool on the PC and prepared for re-connection.

NOTE:

Switching OFF the EZ10 by disconnecting the external power supply line requires to wait

enough time (depending on the HW version!) that the load capacitor of the DC/DC converter inside
the EZ10 discharges so that the GSM862 module inside goes to OFF condition.

5.1 Step-by-Step upgrade procedure

I. Collect information about the Hardware and implemented version of Software by the

command
- AT+CGMR<enter>, which returns the Software version information;
- AT+CGMM<enter>, which returns the Model Identification.

II. Verify the need for the update and check the availability of the software for the Model and

version of the EZ10, requesting it at this e-mail address:

mailto:[email protected]

Receive or download the specific software for upgrading (Transfer Flash Image
GM862_xxx.zip), ca. 5-6 MB at present.

III. Unzip the file GM862_xxx.zip. A new exe file will be created.

IV. Disconnect the EZ10 Terminal from its Power Supply and prepare for re-connection at the

prompt of the running update tool.

V. Run the file

TFI_GM862-xxx_xxxx.exe

. The following window should be displayed, Select

the language preferred by pressing the correspondent button.

VI. Press OK to the initial message.

NOTE: In connection with the EZ10 Terminals, charged battery has to be understood that the

power supply should not be disconnected or break down during the firmware update.

«
...
63
64
65
66
67
...
»

Summary of Contents for EZ10 Series











































































Reviews:

No comments

Related manuals for EZ10 Series

Zlinx Xtreme ZXT9-RM

Brand: B&B Electronics Pages: 163

Brand: u-blox Pages: 79

DSL-302G - 8 Mbps DSL Modem

Brand: D-Link Pages: 11

Brand: Novatel Pages: 35

PlantLinc PLR5000

Brand: Data-Linc Group Pages: 31

Brand: Zte Pages: 30

Brand: Barnett Engineering Pages: 26

Brand: tell Pages: 11

Brand: Etisalat Pages: 30

MA01-A C 4020 Series

Brand: Ebyte Pages: 41

Brand: GDI Pages: 7

Brand: GDI Pages: 16

EtherLink 3C900B

Brand: 3Com Pages: 154

Brand: Comnet Pages: 46

Brand: Planet Networking & Communication Pages: 2

Brand: Hughes Pages: 132

IBOS Cellular Modem

Brand: Philadelphia Scientific Pages: 16

Brand: Zhone Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands