background image

Picotrack 4G User Manual V1.2 

  Seite 19 

 

 

Vehicle - Medium Resolution - Off by Motion 

Position messages are generated either after 5 km distance or as soon as the driving direction 
has been changed more than 45 degrees provided that the vehicle is exceeding 20Km/h.  
Driving long distances will be covered by one position message every 5 km, driving short 
distances is managed by generating position messages whenever the driving direction is 
significantly changed.   
As soon as the vehicle has stopped (detected by sensor) the device will go to sleep mode. When 
vehicle goes back to move, the device will automatically resume tracking. 
Power mode: motion-sleep mode (

5

Distance interval: 

5,000 

Course change:

 

45

 

degrees 

Minimum Speed:

 

20

 

Km/h 

In addition the following extra messages are generated and sent to the server: 

 

Power On 

 

Ignition signal on / off 

 

Digital Input 2 signal on / off 

 

Device stopped moving (

1 minute

 without any sensor motion detection) 

 

Device started moving (according motion sensitivity level 

3

Configuration SMS: 
0011{6digitsIMEI),,,,0,

5000

,020000700000,

5

0000009,

2

000020000

2222

0000000000

22

000000,,,,,,0,

0,0,0,24,,,,

3

,

60

,,,,

45

,

20 

 

 

Vehicle - Low Resolution Track (10min interval) 

Position messages are generated in 10 minutes time intervals regardless of motion, speed or 
changes of driving direction. 
This profile should be used for long distance tracking applications. 
Power mode: timer-sleep mode (

4

Time interval: 

600

 

sec 

Configuration SMS: 
0011{6digitsIMEI},,,,

600

,0,200000700000,

4

0000009,00000000000000000000000000000000,,,,,,0,0,

0,0,24,,,,3,60, 
 

 

Vehicle - High Resolution Track - Off by Ignition 

When the ignition is on, position messages are generated and sent either after an 1 km distance 
has been travelled or as soon as the driving direction has been changed more than 30 degrees; 
additionally a position message is sent every 5 minutes.  
Driving long distances will be covered by one position message every km, driving short distances 
is managed by generating position messages as soon as the driving direction is changed more 
than 30 deg. 
As soon as the Ignition signal is detected as off, the Picotrack will enter the sleep mode.  
This profile should be used for all kind of tracking applications where a high accurate position 
track is needed. 

Summary of Contents for Picotrack

























Reviews: