background image

Qtanium 400 | Installation Manual 

 

iv

 

 

Disclaimer 

It is the Owner’s sole responsibility to install and use the Qtanium 400 (the Product) in a manner that will 
not cause accidents, personal injury or property damage. For the purpose of this notice, “Owner”, “you” 
and “your” means the party (including any person authorized by that party to use and/or install the 
Product) that has either: (a) purchased the Product; (b) leased or rented the Product from Teletrac 
Navman or its related companies; or (c) subscribes to Teletrac Navman’s subscription service and such 
subscription incorporates the use of the Qtanium 400 product. 
 
The Owner of this Product is solely responsible for observing safe driving practices.  
The choice, location and installation of all components of the Product is critical. If installation is not 
correct, the Product may not perform at its designed potential or specifications. If in doubt, consult your 
Teletrac Navman dealer.  
 
The Qtanium 400 is sealed in the factory and tested for watertight integrity. Unauthorized opening of the 
unit will compromise the IP-67 rating, will invalidate the warranty, and may result in failure due to ingress 
of water or other substances.  
 
TO THE MAXIMUM EXTENT PERMITTED BY LAW, ALL REPRESENTATIONS AND WARRANTIES (EXCEPT ANY 
WHICH MAY NOT LAWFULLY BE EXCLUDED) ARE, EXPRESSLY EXCLUDED, INCLUDING WITHOUT PREJUDICE 
TO THE, GENERALITY OF THE FOREGOING, THE IMPLIED WARRANTIES OR MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE. TO THE MAXIMUM EXTENT PERMITTED BY LAW TELETRAC 
NAVMAN DISCLAIMS ALL LIABILITY ARISING OUT OF OR IN CONNECTION WITH THE PRODUCT (INCLUDING 
ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR VIOLATE THE LAW). 
 
As Teletrac Navman is continuously improving this Product, Teletrac Navman may make changes to the 
Product at any time which may not be reflected in this document. Please contact your nearest Teletrac 
Navman office if you require any further assistance. 
 
TELETRAC NAVMAN DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE 
ACCIDENTS, DAMAGE OR VIOLATE THE LAW. 
 
EMC Compliance 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 
 
Copyright 
© 2016 Teletrac Navman Holdings L. P. Teletrac Navman is a registered trademark of Teletrac Navman 
Holdings L. P. All rights reserved. All other trademarks and registrations are the property of their 
respective owners. 

 

Summary of Contents for Qtanium 400




























Reviews: