Telegesis ETRX2USB Command Manual Download Page 48

Page: 48 / 101

R305 AT Commands

- 48 -

AT Command Manual (Rev 3.05)

4 S-Registers

Most S-Registers of the ETRX2 can be read and written locally as well as remotely. The S-
Registers are summarised in the table below.

S-Register Overview

Local R/W

Remote R/W

S00

Channel Mask

( / )

S01

Transmit Power Level

( / )

S02

Preferred PAN ID

( / )

S03

Preferred Extended PAN ID

( / )

S04

Local EUI

( /-)

S05

Local NodeID

( /-)

S06

Parent‟s EUI

( /-)

S07

Parent

‟s NodeID

( /-)

S08

Network Key

(-/ )

S09

Link Key

(-/ )

S0A

Main Function

( / )

S0B

User Readable Name

( / )

S0C

Password

( / )

S0D

Device Information

( /-)

S0E

Prompt Enable 1

( / )

S0F

Prompt Enable 2

( / )

S10

Extended Function

( / )

S11

Device Specific

( / )

S12

UART Setup

( / )

S13

Pull-up enable

( / )

S14

Pull-down enable

( / )

S15

I/O Configuration

( / )

S16

Data Direction of I/O Port

(volatile)

( / )

S17

Initial Value of S16

( / )

S18

Output Buffer of I/O Port

(volatile)

( / )

S19

Initial Value of S18

( / )

S1A

Input Buffer of I/O Port

(volatile)

( /-)

S1B

Special Function pin 1

(volatile)

( / )

S1C

Initial Value of S1B

( / )

S1D

Special Function Pin 2

(volatile)

( / )

S1E

Initial Value of S1D

( / )

S1F

A/D1 (ETRX3: ADC0)

( /-)

S20

A/D2 (ETRX3: ADC1)

( /-)

S21

A/D3 (ETRX3: ADC2)

( /-)

S22

A/D4 (ETRX3: ADC3)

( /-)

S23

Immediate functionality at IRQ0

( / )

S24

Immediate functionality at IRQ1

( / )

S25

Immediate functionality at IRQ2

( / )

S26

Immediate functionality at IRQ3

( / )

Password Protected Registers

Summary of Contents for ETRX2USB






































































































Search results

Summary of Contents for ETRX2USB

Reviews:

Telegesis ETRX2USB, Command Manual, Page: 48 / 101

Search results

Summary of Contents for ETRX2USB

Reviews: