manualshive.com logo in svg

Telegesis ETRX2USB, Command Manual, Page: 57 / 101

Share
Download
Telegesis ETRX2USB Command Manual Download Page 57

 

 

R305 AT Commands

 

 

©2011 Telegesis (UK) Ltd 

- 57 - 

 AT Command Manual (Rev 3.05) 

S0B 

– User Readable Name 

Description 

Password protected user defined name which 
can be used to identify the node 
 

Operations 

R/W LOCAL 
R/W REMOTE   

 

Write operation 

ATS0B=<name>:<password> 
ATREMS:<address>,0B=<name>:<password> 
 

Becomes effective 

Instantly

 

 

Storage 

Non-Volatile 

Parameters 

cccccccccccccccc 

 
 

Name with up to 16 characters. 
 
 
 
 
 
 
 
 
 

 
Factory Default 

Telegesis 

SW release  

R302   

 

 

 

 

    

● 

 

 

S0C 

– Password 

Description 

The local node

‟s password.  

 

Operations 

W LOCAL 
W REMOTE   
 

Write operation 

ATS0C=<NEW>:<OLD> 
ATREMS:<address>,0C=<NEW>:<OLD> 
 

Becomes effective 

Instantly

 

 

Storage 

Non-Volatile 

Parameters 

cccccccc 

 

8 case sensitive characters (8 bytes).  
Note  that  the  password 

must

  have  exactly  8 

characters. 
 
 

 

 
 

 

 
 

Factory Default 

password 

SW release  

R300   

 

 

 

 

        

● 

 

Summary of Contents for ETRX2USB






































































































Reviews:

No comments