Telegesis ETRX2USB Command Manual Download Page 65 | Manualshive

Page: 65 / 101

Telegesis ETRX2USB Command Manual Download Page 65

R305 AT Commands

©2011 Telegesis (UK) Ltd

- 65 -

AT Command Manual (Rev 3.05)

S15

– ETRX3: I/O Configuration ETRX2: Reserved

Description

This Register is not used on the ETRX2. On
the  ETRX3  it  is  used  to  enable  alternate
functionalities  for  each  I/O  pin.  When  set  to
zero the corresponding I/O pin is a standard
I/O  pin,  when  set  to  1  any  other  setting  for
this  I/O  are  overwritten  by  the  peripheral
functionality.

representing the I/O pins

xxxxxxxx
<PC7…PC0><PB7…PB0><PA7…PA0>

Operations

R/W LOCAL
R/W REMOTE

Becomes effective

After Reset

Storage

Non-Volatile

Parameters

XXXXXXXX

Where

XXXXXXXX

represents

a

32-bit

hexadecimal number.

bit 31 reserved
bit 30 reserved
bit 29 reserved
bit 28 reserved
bit 27 reserved
bit 26 reserved
bit 25 reserved
bit 24  reserved

bit 23 reserved (PC7)
bit 22 reserved (PC6)
bit 21 Set: Enable TX_Active (reserved on

–LR)

bit 20 reserved (PC4)
bit 19 reserved (PC3)
bit 18 reserved (PC2)
bit 17 Set: Enable ADC3 (PC1)
bit 16 reserved (PC0)

bit 15 Set: Enable ADC2 (PB7)
bit 14 Set: Enable ADC1 (PB6)
bit 13 Set: Enable ADC0 (PB5)
bit 12 Set: reserved
bit 11 Set: reserved
bit 10 Set: Enable RXD input (PB2)
bit 9 Set: Enable TXD output (PB1)
bit 8 Set: Enable Vref Output (PB0)

bit 7 reserved (PA7)
bit 6 reserved (PA6)
bit 5 reserved (PA5)
bit 4 reserved (PA4)
bit 3 reserved (PA3)
bit 2 reserved (PA2)
bit 1 reserved (PA1)
bit 0 reserved (PA0)

Factory Default

00000600

SW release

R300

«
...
63
64
65
66
67
...
»

Summary of Contents for ETRX2USB






































































































Reviews:

No comments