manualshive.com logo in svg

TELEFONICA P660HW-B1A, User Manual

Share
Download
TELEFONICA P660HW-B1A User Manual Download Page 14

 
 

11

 

LED 

Status 

Description 

The self-testing of the power fails if the LED is 

always red. 

Blink Red  Upgrading software. 

Off 

DSL link not established. 

Slow 

Blink 

Green 

DSL line is training. 

Fast Blink 

Green 

DSL interface is TX/RX packets. 

CONEXIÓN 

Green 

DSL link established. 

Off 

No PPPoA or PPPoE connection 

Green 

The PPPoA or PPPoE connection is 

established. The users can access the 

Internet. 

Internet 

Red 

Device attempts to become IP connected but 

fails (no DHCP response, no PPPoE 

response, PPPoE authentication failed, no IP 

address from IPCP, etc.) 

Off 

No Ethernet signal is detected. 

Blink 

Green 

The user data is passing through Ethernet 

port. 

Ethernet 

Green 

Ethernet interface is ready to work 

Off 

WLAN interface disable. 

Blink 

Green 

WLAN interface is TX/RX packets. 

WLAN 

Green 

WLAN interface enable. 

Off 

Off: WPS process is inactive 

WPS 

Green 

WPS process is on going 

Summary of Contents for P660HW-B1A





















Reviews:

No comments

Brands by name

Popular brands

Load more brands