background image

Page   

User Manual: MV3-E Hybrid Controls

Notice to Boat Manufacturer, Installer, and Consumer

Please read these instructions through carefully and entirely before beginning installation or operation. This 
manual must be accessible to the owner/user of this Teleflex Marine product.
Throughout this manual, warnings are used to alert the installer/operator to special instructions concerning a 
particular service or operation that may be hazardous if performed incorrectly or carelessly.  Observe these 
alerts carefully!

These “safety alerts” alone cannot eliminate the hazards that they signal.  Strict compliance to these special 
instructions when performing installation, operation, and maintenance plus “common sense” operation are the 
most effective accident prevention measures.

This device should not be used as a navigational aid to prevent collision, grounding, boat damage, or personal 
injury.  When the boat is moving, water depth may change too quickly to allow time for you to react.  Always 
operate the boat at very slow speeds if you suspect shallow water or submerged objects.

Disassembly and repair of this electronic unit should only be performed by authorized service personnel.  Any 
modification of the serial number or attempt to repair the original equipment or accessories by unauthorized 
individuals will void the warranty.  Handling and/or opening this unit may result in exposure to lead, in the form 
of solder.

This product contains lead, a chemical known to the State of California to cause cancer, birth defects, and other 
reproductive harm.

The  information  contained  in  this  manual  is  believed  to  be  accurate  at  the  time  of  going  to  print  but  no  responsibility,  direct  or 
consequential, can be accepted for damage resulting from the use of this information.  The manufacturers reserve the right to make 
changes, without notice, to any of its products.

Warning

Warning

Summary of Contents for MV3-E Series

















Reviews: