manualshive.com logo in svg

Teledyne HVG-2020A, Instruction Manual, Page: 4 / 29

Share
Download
Teledyne HVG-2020A Instruction Manual Download Page 4

HVG-2020A Instruction Manual

 

Page 4 of 29 

5.

 

DIGITAL OPERATION ....................................................................................................... 19

 

 

I

NSTRUMENT 

S

TATES

 ..................................................................................................... 19

 

 

S

ERIAL 

C

OMMUNICATIONS

 ................................................................................................ 19

 

5.2.1.

 

General .......................................................................................................... 19

 

5.2.2.

 

Serial Communication Software ............................................................................ 19

 

5.2.3.

 

The Sensor List................................................................................................. 19

 

5.2.4.

 

Command Prompt ............................................................................................. 19

 

5.2.5.

 

Command Format ............................................................................................. 19

 

5.2.6.

 

RS232 / RS485 Mode .......................................................................................... 20

 

5.2.7.

 

Response Format .............................................................................................. 20

 

5.2.7.1.

 

Response Line Termination ......................................................................................... 20

 

5.2.7.2.

 

RS485 Mode Responses .............................................................................................. 21

 

5.2.8.

 

Commands ...................................................................................................... 21

 

5.2.8.1.

 

Reporting Commands ................................................................................................ 21

 

5.2.8.2.

 

System Commands ................................................................................................... 21

 

5.2.8.3.

 

State Commands ..................................................................................................... 23

 

5.2.8.4.

 

Sensor List Commands .............................................................................................. 24

 

6.

 

TROUBLESHOOTING ....................................................................................................... 27

 

 

A

UTHORIZED 

M

AINTENANCE

 .............................................................................................. 27

 

 

T

ROUBLESHOOTING

 ...................................................................................................... 27

 

6.2.1.

 

Instrument Lists and Codes .................................................................................. 27

 

6.2.2.

 

Possible Problems and Solutions............................................................................ 27

 

7.

 

WARRANTY .................................................................................................................. 28

 

 

W

ARRANTY 

P

OLICY

 ....................................................................................................... 28

 

 

R

ETURN 

P

OLICY

 .......................................................................................................... 28

 

8.

 

DRAWINGS ................................................................................................................... 29

 

 

Summary of Contents for HVG-2020A






























Reviews:

No comments