manualshive.com logo in svg

Teledyne HVG-2020A, Instruction Manual, Page: 17 / 29

Share
Download
Teledyne HVG-2020A Instruction Manual Download Page 17

HVG-2020A Instruction Manual

 

Page 17 of 29 

3.3.1.  Screen Orientation 

The top of the screen is indicated and will rotate 90° each time the screen is pressed. 

3.3.2.  Set Zero 

The Set Zero menu will set the pressure reading to zero and should only be done if the actual pressure 

is known to be well below 0.1 Torr. If the pressure reading is too large, a warning screen will appear 

asking if the user is certain they want to do this operation. 

3.3.3.  Device Info 

The user may view the serial number, analog output setting, calibration date, gauge type, and the I/O 

and main board firmware revision levels. 

 

3.3.4.  Analog Output 

The user may select 0 – 1 V, 0 – 5 V, 0 – 10 V, 0 – 20 mA or 4 – 20 mA. 

3.3.5.  Serial Port 

The user may select either RS232 or RS485 serial communications. After selecting the type, pressing 

the arrow icon will take the user to the baud rate selection There are 5 baud rates available: 9600, 

19200, 38400, 57600 and 115200. If RS485 was selected, additional sub-menu screens will appear 

allowing the user to select the address and termination resistor state. At the end of the selection sub-

menus, the user can accept or canel the selections shown. 

3.3.6.  Restore Factory Defaults 

This selection allows the user to reset the configuration of the gauge back to its original factory setup. 

A warning screen will appear asking if the user is certain they want to perform this operation. 

 

 

Summary of Contents for HVG-2020A






























Reviews:

No comments