Teledyne ADQ8-4X Manual Download Page 3 | Manualshive

Page: 3 / 46

Teledyne ADQ8-4X Manual Download Page 3

19-2302 A
2020-09-16

3(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

3(46)

4.12.2Frame sync output on SYNC connector .................................................................................... 26
4.12.3Triggering external equipment with internal trigger.................................................................... 27

4.13 Large scale integration trigger support ........................................................................ 28

4.13.1Distributing trigger......................................................................................................................  28
4.13.2Clock reference..........................................................................................................................  28
4.13.3High precision trigger on analog input .......................................................................................  28
4.13.4Calibration..................................................................................................................................  28

CLOCK......................................................................................................................... 30

Clock domains ............................................................................................................. 30

Flexible clock network.................................................................................................. 30

ADQ8-4X-PCIe front panel connectors........................................................................ 31

Internal clock reference................................................................................................ 31

External clock reference .............................................................................................. 31

Clock reference phase tuning ...................................................................................... 32

Internal clock generator ............................................................................................... 32

External clock............................................................................................................... 32

Clock reference output................................................................................................. 32

5.10 Sample skip ................................................................................................................. 32

GPIO ............................................................................................................................ 33

GPIO on TRIG connector............................................................................................. 33

ADQ8-4X–PXIe GPIO on SYNC connectors ............................................................... 34

Using GPIO as a trigger............................................................................................... 34

Output .......................................................................................................................... 34

GPIO in ADQ Development Kit .................................................................................... 34

ACQUISITION CONTROL ........................................................................................... 35

Multi-thread notice ....................................................................................................... 35

Acquisition memory...................................................................................................... 35

Triggered streaming acquisition................................................................................... 36

Acquisition mode multi-record...................................................................................... 36

Re-arm time ................................................................................................................. 37

User scheduled data transfer mode............................................................................. 38

7.6.1 Transfer buffers ......................................................................................................................... 40
7.6.2 User’s buffers............................................................................................................................. 40

Streaming transfer mode ............................................................................................. 40

Users application software consuming data ................................................................ 40

Record header ............................................................................................................. 41

7.9.1 Metadata....................................................................................................................................  41
7.9.2 Record Status ............................................................................................................................  41
7.9.3 User ID.......................................................................................................................................  42
7.9.4 Serial number ............................................................................................................................  42
7.9.5 Channel .....................................................................................................................................  42
7.9.6 Record number ..........................................................................................................................  42
7.9.7 Data format ................................................................................................................................  42
7.9.8 Record length ............................................................................................................................  42

7.10 Over-range and under-range ....................................................................................... 43

HOST PC CONNECTION............................................................................................ 44

PCI Express interface .................................................................................................. 44

Using several units....................................................................................................... 44

8.2.1 Using several digitizers from a single application. ..................................................................... 44
8.2.2 Using several digitizers from a several applications. ................................................................. 44

«
1
2
3
4
5
...
»

Summary of Contents for ADQ8-4X















































Reviews:

No comments