Teledyne ADQ8-4X Manual Download Page 29 | Manualshive

Page: 29 / 46

Teledyne ADQ8-4X Manual Download Page 29

19-2302 A
2020-09-16

29(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

29(46)

#

DESCRIPTION

USER COMMAND

Daisy chain block contains of one primary and secondary units. There is a
set of general functions to manage the operation.

DaisyChainReset
DaisyChainEnable
DasiyChainSetMode
DasiyChainSetOutputState

a

The common clock reference guarantee the phase stability between all
units.

SetClockSource
AdjustClockReferenceDelay

b

Select a trigger source in the primary unit. This may be an analog channel
using level trigger or any other trigger source

DaisyChainSetTriggerSource
DaisyChainSetupLevelTrigger

c

The trigger signal is synchronized to the clock reference and forwarded to
the secondary units. This daisy chain of triggers can include many cards.

DaisyChainSetupOutput
DaisyChainEnableOutput

d

The data is triggered on the synchronized trigger signal.

Data acquisition control
commands

e

The trig time is sent to the ADQAPI where the trigger position of all the
channels is aligned.

DaisyChainGetTriggerInformat
ion

Figure 20: Daisy Chain Trigger.

, -

,-

$$.#

#

/.

##

$

$$#

#

&0#

,#-

$0

$$#

1

2

3

$# #

#$

"

%

40

&

$

"

#

&#$

$$.#

#

/.

$0

$$

1

2

3

"

1

2

3

&0#

"

&0#

,-

,-

,-

,-

,-

«
...
27
28
29
30
31
...
»

Summary of Contents for ADQ8-4X















































Reviews:

No comments