Teledyne ADQ8-4X Manual Download Page 28 | Manualshive

Page: 28 / 46

Teledyne ADQ8-4X Manual Download Page 28

19-2302 A
2020-09-16

28(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

28(46)

4.13 Large scale integration trigger support

The ADQ8-4X supports integration into a large scale PXIe chassis for single shot applications, The
function is described in the manual

. This section is only a short introduction.

4.13.1 Distributing trigger

The trigger is distributed to the boards via the SYNC input and output. The trigger distribution is daisy
chained, so there is no limit to the number of boards.

4.13.2 Clock reference

Use the clock reference distribution in the backplane of the chassis for phase alignment of the digitizers
in the system.

4.13.3 High precision trigger on analog input

The source for the trigger can be any available trigger. If one of the analog inputs is used as a high pre-
cision input, the trigger timing can be computed to 25 ps trigger precision.

4.13.4 Calibration

To reach the trigger accuracy of 200 ps for the entire chassis installation, the system has to be cali-
brated in the factory

.

#

DESCRIPTION

USER COMMAND

REF

a

Internal trigger generator

SetInternalTriggerPeriod

b

Select internal trigger as output

SetupTriggerOutput

c

The trigger output and the external trigger input are electrically connected
inside the digitizer

d

Select

external

trigger as trigger source

SetTriggerMode

e

Acquisition engine creates a record from streaming data

Figure 19: External routing of internal trigger.

%

&'

&'

()

*

+

,!

,

#

,

-.-/

.

.

) )

)

&0'

&'

&'

%

%()*

&'

«
...
26
27
28
29
30
...
»

Summary of Contents for ADQ8-4X















































Reviews:

No comments