manualshive.com logo in svg

Teledyne Lecroy CP031, Operator'S Manual

Share
Download
Teledyne Lecroy CP031 Operator'S Manual Download Page 5

Operator’s Manual 

Contents 

Safety Instructions ................................................................................................................................ 1

 

Symbols .............................................................................................................................................. 1

 

Precautions ........................................................................................................................................ 1

 

Introduction ............................................................................................................................................ 3

 

Specifications ........................................................................................................................................ 3

 

Warranted Characteristics ................................................................................................................ 3

 

Nominal Characteristics .................................................................................................................... 4

 

Typical Characteristics ...................................................................................................................... 4

 

Environmental Characteristics ......................................................................................................... 5

 

Physical Characteristics ................................................................................................................... 5

 

Safety Ratings .................................................................................................................................... 5

 

CP030/CP030A Maximum Input Current vs. Frequency ................................................................ 6

 

CP030/CP030A Insertion Impedance vs. Frequency ...................................................................... 6

 

CP031/CP031A Maximum Input Current vs. Frequency ................................................................ 7

 

CP031/CP031A Insertion Impedance vs. Frequency ...................................................................... 7

 

Operation ................................................................................................................................................ 8

 

Precautions ........................................................................................................................................ 8

 

Connecting to the Test Instrument .................................................................................................. 8

 

Connecting to the Test Circuit .......................................................................................................... 8

 

Operating with an Oscilloscope ........................................................................................................ 9

 

Performance Verification ....................................................................................................................11

 

Test Equipment Required ................................................................................................................11

 

Preliminary Procedure .....................................................................................................................12

 

Functional Check .............................................................................................................................13

 

Check LF Accuracy ..........................................................................................................................13

 

 

i 

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for CP031





























Reviews:

No comments

Brands by name

Popular brands

Load more brands