background image

SI-125 Power Amplifier Manual 

 

LIMITED WARRANTY POLICY 

Telecor Inc. warrants all products bearing the Telecor name to be free from defects in material and 
workmanship under normal use and service for a period of one year from date of delivery. Telecor will 
repair or replace (at our option), free of charge, any unit that is found to be defective and returned to us 
under warranty. Telecor warrants all other products made by others, and distributed by us, to be covered 
by the manufacturers' warranty period. 
 
This warranty shall not apply to any Telecor products that have been subject to misuse, neglect, accident, 
modification, water, fire, lightning, paint, or used in violation of instructions furnished, repaired or altered 
outside of the factory. This warranty does not cover batteries, bulbs, fuses or damage caused by batteries 
used in connection with the product. Telecor reserves the right to make the final decision on whether 
there is a defect in materials or workmanship, and whether or not the product returned is within the 
warranty period. 
 
This warranty covers bench repairs only. Telecor will not be responsible for any costs incurred involving 
on-site service calls. Repair or replacement by others, fire, transportation, labor charges, indemnity, etc., 
are not covered by this warranty and no responsibility for same will be assumed by us. Our liability does 
not extend to consequential damage. 
 

AUTHORIZED REPAIR STATION: 

All participating Distributors and Dealers are authorized to accept Telecor products for return to us for 
repair or replacement, or customers may return goods to us directly, providing that return authorization 
has been obtained. 
 

U. S. customers are required to ship any returns or repairs to: 

 Telecor 

Inc. 

 

2434 Jerauld Avenue 

* U. S. customers must not 

 

Niagara Falls, New York 

return products to Canada

 

 USA, 

14305 

 

Canadian and all International customers are required to ship any returns or repairs to: 

 Telecor 

Inc. 

 6205 

Kestrel 

Road 

 Mississauga, 

Ontario 

 Canada, 

L5T 

2A1 

 
For details on Telecor’s Return Policy, see our Published Merchandise Return Policy. 
 
E:\T2-108\T2-M108-ABC\T2-M108-B.doc/AD 
 
© Copyright 2016 by Telecor Incorporated. All rights reserved. No part of this publication may be 
reproduced in any form, or by any means, without the prior written permission of Telecor Incorporated. 
 
Telecor Inc. makes no representation of warranties with respect to this manual. Furthermore, Telecor 
reserves the right to make changes in the specifications of the products described in this manual at any 
time without notice, and without obligation of Telecor to notify any persons of such revisions or changes. 
 
www.telecor.com

 

 

Summary of Contents for SI-125










Reviews: