background image

11

3.3 Exclusion of safety edge in the last 5 cm of the closure 

In case of uneven floors, it could be necessary deactivating the safety edge in the last part of the closure (not 
more than 5 cm to comply with the standards) in order to avoid any accidental activation of the safety edge.
This procedure must be performed by qualified installer only, who will take charge of its correct application.

WARNING: this procedure can be used only for doors which require more than 10 seconds each manoeuvre. The 
exclusion of the safety edge is applied only if the closure starts from the upper limit switch and it is not stopped.

Open the door 

completely 

by means of 

a memorized transmitter. The buzzer emits 
a long beep when the upper limit switch is 
reached. Put on the floor, exactely under the 
door, a sturdy object not more than 5 cm high.
Close the door (in 

hold-to-run

 mode), with 

no interruption

. The door will stop at the 

obstacle and the control unit will make a 
long beep. Open the door 

completely 

and 

remove the object. Close the door to verify the 
correct application of the procedure.

hold-to-run

DEACTIVATION

Press P1 button 

ten times

 and keep it 

pressed for 

5 seconds

. The buzzer emits 

3 beeps.

WITHIN 30 SEC. FROM POWER-ON

(       5 s)

keep it 

pressed

(       5 s)

keep it 

pressed

Press P1 button 

eleven times

 and keep it 

pressed for 

5 seconds

. The buzzer emits 5 

beeps.

10x

11x

WITHIN 30 SEC. FROM POWER-ON

P1

P1

max. 5 cm

X

Summary of Contents for TVNRG868A01





















Reviews: