•
“
regusr=
”
, or
“
rusr=
”
, this parameter allows you to configure a user if the registration APN requires authentication.
•
“
regpwd=
”
, or
“
rpwd=
”
this parameter allows you to configure a password if the registration APN requires authen-
tication.
•
“
wband=
”
, or
“
wb =
”
this parameter allows to select WCDMA bands. You need to provide a list of band numbers
separated by commas, for example "wb=1,2,3". To disable all bands, use the word "none".
•
“
lband=
”
, or
“
lb =
”
this parameter allows you to select LTE bands. You need to provide a list of band numbers
separated by commas, for example "lb=3,7,20". To disable all bands, use the word "none".
•
“
arp=1
”
, this parameter configures the 4Ge to act as a modem, answering every ARP request received in VLAN
463 with its own MAC address, as if it were the owner of the requested IP address. This setup supports host
routers that are not able to update the "next hop" of configured static routes using the DHCP-provided gateway to
the VLAN 463 interface and/or modify the cost of DHCP-learned routes (which causes the interface to be con-
sidered a Point-to-Point one, something that is conceptually wrong in Ethernet media). When using this mode, you
may/should add a route with VLAN 463 subinterface as output/next-hop gateway to the host router configuration.
Command history:
Release
Modification
10.09.15, 11.00.02, 11.01.00
The
"profilenum"
parameter was introduced.
10.09.15, 11.00.02, 11.01.00
The
"pnum"
(short form for
"profilenum"
) parameter was introduced.
10.08.42, 10.09.18, 11.00.02, 11.01.00
The
"regusr"
parameter was introduced.
10.08.42, 10.09.18, 11.00.02, 11.01.00
The
"regpwd"
parameter was introduced.
10.08.42, 10.09.18, 11.00.02, 11.01.00
The
"regauth"
parameter was introduced.
11.00.07, 11.01.02
The
"mode"
parameter now accepts values
"cdma"
,
"hrpd"
and
"hy-
brid"
.
10.09.31, 11.00.07, 11.01.04
The short form for the
"regusr"
parameter was enabled.
10.09.31, 11.00.07, 11.01.04
The short form for the
"regpwd"
parameter was enabled .
10.09.31, 11.00.07, 11.01.04
The short form for the
"regauth"
parameter was enabled.
10.09.31, 11.00.07, 11.01.04
The short form for the
"apntype"
parameter was enabled.
10.09.31, 11.00.07, 11.01.04
The short form for the
"regapn"
parameter was enabled.
10.09.31, 11.00.07, 11.01.04
The short form for the
"regapntype"
parameter was enabled.
10.09.31, 11.00.07, 11.01.04
The
"lband"
parameter was introduced.
10.09.31, 11.00.07, 11.01.04
The
"wband"
parameter was introduced.
10.09.31, 11.00.07, 11.01.04
The
"arp"
parameter was introduced.
Note
Remember to change the values in the example to the values that are specific to your application.
Be very careful when entering the PIN code for the SIM card that will be installed in the Teldat 4Ge.
Entering an incorrect PIN may block the SIM.
If you enter the PIN incorrectly, the Teldat 4Ge router will not try to use the SIM again until the PIN has
been changed or the device rebooted.
3.2 Configuring a Teldat router
As with a Cisco router, you can connect a Teldat router to the Teldat 4Ge through an Ethernet subinterface belong-
ing to VLAN 463.
The following configuration example shows how to connect a Teldat router:
log-command-errors
no configuration
set hostname 4Ge
3 Configuration
Teldat S.A.
10
Teldat 4Ge
