manualshive.com logo in svg

Tekvox TEK 1201-MV, User Manual

Share
Download
Tekvox TEK 1201-MV User Manual Download Page 6

 

www.tekvox.com 

1201-MV 

79033-MV User Manual 

1. Product Introduction

 

The 1201-MV is a universal switcher that supports 4Kx2K@60Hz 4:4:4, flexible multiview modes, and 
six video inputs: five HDMI, and one powered USB-C. The 1201-MV includes simultaneous HDMI & 
HDBaseT outputs, LAN bridge extension, and a simulated USB 3.0 hub extender with bridging to the 
USB-C input. The HDMI output can be configured to mirror the HDBaseT output or preview the HDMI 
1 input. The HDBaseT output can travel up to 328 feet (100m) without any additional amplification, 
and supports PoC for remotely powering the receiver. 
 
The 1201-MV also features automatic source detection & switching, can power displays on and off 
using CEC or RS232, and offers versatile multiview for showing up to four sources on-screen 
simultaneously. The universal switcher can extend USB signals

—

such as cameras and 

microphones

—

from the far-end hub, making them available to the system PC or a connected laptop. 

The 1201-MV is available with or without its hub/receiver.  

1.1 Features 

Video 

 

• 

5 HDMI inputs & 1 USB-C input with 60W charging  

• 

EDID settings for all inputs 

–

 Default is 1080P/60  

• 

Supports an Auto-Switching mode with automatic display power  

• 

Supports HDMI output resolutions up to 4Kx2K @ 60Hz 4:4:4  

• 

Supports HDBaseT output resolutions up to 4Kx2K @ 60Hz 4:2:0  

• 

Default output resolution is 1080P/60  

• 

12 flexible multiview configurations for showing up to 4 sources at once  

• 

Breakaway HDMI output can preview the HDMI 1 input or mirror the HDBaseT output  

• 

328 ft HDBaseT transmission with controllable PoC power 

• 

Hub receiver supports PoC power with 12 ~ 48V range 

Audio 

 

• 

Independent audio input selection during Multiview operation  

• 

Supports both source and mic levels  

• 

Mic with phantom power selection  

• 

Line input for mic mixing  

Control 

 

• 

Controllable via RS232, IR remote, front panel buttons, or TCP/IP commands  

• 

RS232 and TCP/IP use a unique, easy-to-use ASCII protocol  

• 

Two RS232 control modes: 

• 

Control of the switcher from both the switcher and hub/receiver (Default)  

• 

Sending RS232 display commands with baud rate setting to the hub/receiver  

• 

Supports sending TEVOX Macro commands for TekMonitor control  

• 

CEC control of displays and receivers  

• 

User-defined CEC commands 

Summary of Contents for TEK 1201-MV























































Reviews:

No comments

Brands by name

Popular brands

Load more brands